Frigidaire MWV150KB, Руководство по установке

Страница: 20 / 72

INSTALLATION OVERVIEW
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C4.
C5. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
•
Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
Installation Instructions
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bott m of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION:
Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts. 4
3
ATTACH THE MOUNTING
PLATE TO THE WALL C1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to
3 ⁄
4
″ (19 mm) onto
each bolt.
1
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
2
RECIRCULATING
(Non-Vented Ductless)
C
Install or change Charcoal Filter
C3. Check Blower Plate
o
EN-20
3/8" TO EDGE
  
 

 



NOTE: IT IS VERY IMPORT
ANT TO
READ AND FOLLOW THE
DIRECTIONS
IN THE INSTALLATION INSTRU
CTIONS
BEFORE PROCEEDING W
ITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serve
s to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that th
e template is positioned
accurately. 2. Locate and mark at least o ne stud on the left or
right side of the centerline.
 It is important to use at least
one wood
screw mounted firmly in a stu
d to support the weight
of the microwave. Mark two a dditional, evenly spaced
locations for the supplied tog gle bolts.
3. Drill holes in the marked lo
cations. Where there is
a stud, drill a 3/16" hole fo
r wood screws. For holes
that do not line up with a st ud, drill 5/8" holes for
toggle bolts.
 DO NOT INSTALL THE MOU
NTING PLATE
AT THIS TIME. 4. Remove the template from the rear wall.
5. Review the Installation Inst ruction book for your
installation situation.
Locate and mark holes to al ign with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
STUD ON EITHER SIDE O F
THE CENTERLINE.
MARK THE LOCATION FO R 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLAT
E
AREA.
Locate and mark holes to al
ign with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
STUD ON EITHER SIDE O F
THE CENTERLINE.
MARK THE LOCATION FO
R 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLAT
E
AREA.
Trim the rear wall template al ong the dotted line.
Trim the rear wall template a long the dotted line.




 
12"
4"
Darle vuelta a la hoja para con
sultar la
versión en Español.