Frigidaire MWV150KB, Руководство по установке

Страница: 12 / 72

Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION:
Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL
A1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to
3 ⁄
4
″ (19 mm) onto
each bolt.
1
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
Mount Microwave Oven A5.
Adjust Exhaust Adaptor A6.
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TOP EXHAUST
(Vertical Duct)
A
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
A7. Connect Ductwork
A3.
A4. Check Damper Operation
Adapting Microwave Blower for
Outside Top Exhaust
EN-12
3/8" TO EDGE

 
 





NOTE: IT IS VERY IMPORTANT
TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INST
RUCTIONS
BEFORE PROCEEDING WITH T
HIS
REAR WALL TEMPLATE.
This Rear Wall Template ser
ves to position the bottom
mounting plate and to locate t he horizontal exhaust
outlet.
1. Use a level to check that th
e template is positioned
accurately.
2. Locate and mark at least o
ne stud on the left or
right side of the centerline.
 It is important to use at least one
wood
screw mounted firmly in a stud
to support the weight
of the microwave. Mark two ad ditional, evenly spaced
locations for the supplied tog
gle bolts.
3. Drill holes in the marked lo
cations. Where there is
a stud, drill a 3/16" hole for
wood screws. For holes
that do not line up with a s tud, drill 5/8" holes for
toggle bolts.
 DO NOT INSTALL THE MOUNT
ING PLATE
AT THIS TIME.
4. Remove the template from th e rear wall.
5. Review the Installation Ins
truction book for your
installation situation.
Locate and mark holes to align wit
h holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD O
N EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FO
R 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS I
N THE MOUNTING PLATE
AREA.
Locate and mark holes to align w
ith holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE S
TUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FO
R 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN
THE MOUNTING PLATE
AREA.
Trim the rear wall template along
the dotted line.
Trim the rear wall template along
the dotted line.



 

12"
4"
Darle vuelta a la hoja para cons
ultar la
versión en Español.