background image

owner's manual

 

6

 

 

2) This table is appropriate for the models with only one inverter compressor.

 

 

Table 6-2

 

 

Normal display

 

Display content 

Note

 

1

 

Outdoor unit address

 

0

 

2

 

Outdoor unit capacity

 

8, 10

 

3

 

Modular outdoor unit qty.

 

Available for master unit

 

4

 

Outdoor unit total capacity

 

Capacity requirement

 

5

 

Indoor unit total capacity requirement

 

Available for master unit

 

6

 

The corrected total capacity of unit

 

Available for master unit

 

7

 

Operation mode

 

0, 1, 2, 3, 4

 

8

 

The actual operation capacity of this outdoor unit

 

Capacity requirement

 

9

 

Fan status

 

0, 1, 2

,

3, 4, 5, 6, 7, 8, 9

 

10

 

T2B/T2 average temp.

 

Actual value

 

11

 

T3 pipe temp.

 

Actual value

 

12

 

T4 ambient temp.

 

Actual value

 

13

 

Inverter air discharge temp.

 

Actual value

 

14

 

Fixed frequency 1 air discharge temp.

 

Actual value

 

15

 

Reserved

 

Reserved

 

16

 

Inverter current

 

Actual value

 

17

 

Reserved

 

Reserved

 

18

 

Reserved

 

Reserved

 

19

 

EXV opening angle

 

 

20

 

Air discharge pressure

 

Actual value ×0.1 MPa

 

21

 

The limitation of Indoor unit proformed mode

 

0,1,2,3,4

 

22

 

Indoor unit qty.

 

Actual value

 

23

 

The last time error or protective code

 

Without protection or error displays as 00

 

24

 

- -

 

Spot inspection end

 

 

 

The display contents as followings:

 

1) Normal display: When standby, it displays the indoor unit qty. When receive the capacity requirement, it will 

display the compressor rotation frequency

.

 

2) Operation mode: 0—OFF; 1—Air supply; 2—Cooling; 3—Heating; 4—Constraint cooling.

 

3) Rotation speed: 0—fan stop; 1~9 speed increase sequentially; 9 is the maximum fan speed.

 

4) PMV opening angle: Pulse count= display value × 8

 

5) The limitation of Indoor unit proformed mode : 0—Heating Priority Mode; 1—Cooling Priority Mode; 2—Priority 
Mode; 3—Only Respond The Heating Mode; 4—Only Respond The Cooling Mode.

 

6) Indoor unit qty.: The indoor unit which communicate with outdoor unit normally.

 

 
 

 

7.

 

AFTERSALE SERVICE

 

If the air conditioner was operated abnormally, please plug off the power supply firstly, and contact with Kaysun After-sales Center or 
Special Distributor. For detail please refer to the attached accessory Consumer Service Instruction.

 

Содержание Kaysun K2UF-280 DN3













Отзывы: