5
920-197-01
To set the timer
NOTE:
You can set the
START
and
STOP
times a minimum of one hour
apart, and a maximum of 23 hours apart.
9
TIMER START
- Press
Start
.
g
n
il
o
o
c
r
o
f
e
m
it
t
r
a
t
s
t
n
e
r
r
u
c
e
h
t
w
e
i
v
o
t
Continue pressing the
Start
button until you arrive at the start time
you desire. The start time for cooling will then be set.
10
TIMER STOP
- Press the
Stop
button. Continue pressing the
Stop
button until you arrive at the stop time you desire. The stop time for
cooling will then be set.
11
TIMER ON / OFF
- Press the
On/Off
button to activate (light on) or
deactivate (light off) the timer. Once the on and off times have been
selected, they will remain in memory and cycle daily until changed.
NOTE:
If the unit is unplugged or the power is interrupted, the
Set Hr.
function must be reset or the
On/Off
function will not work.
How to use the remote control
To start unit
1
POWER
- Press the
Power
button once. The unit will automatically
start in the mode and fan speed it was last left on.
To set mode of operation
2
COOL
- Press the
Cool
button to automatically switch the operating
mode to COOL.
3
FAN ONLY
- Press the
Fan Only
button if you want to run the fan
only.
4
MoneySaver
®
- Press the
MoneySaver
®
button to activate the
MoneySaver
®
feature. This feature cycles the fan with the compres-
sor so that the fan does not run all the time.
To adjust temperature setting
5
WARMER
- Press the
Warmer
button to raise the temperature
setting.
6
COOLER
- Press the
Cooler
button to lower the temperature
setting.
To adjust fan speed
7
FAN SPEED
- Press the
Fan Speed
button to see the current set-
ting. Press again to change the fan speed.
F1
is the lowest setting
(
SLEEP / LOW
),
F2
is
MEDIUM
,
F3
is
HIGH
, and
SF
is the
SMART
FAN
setting.
To set the hour clock
8
SET HOUR CLOCK
- Press
Set Hr.
once to see the current clock
setting. Continue pressing the button until you arrive at the current
time (Hour only). Minutes are not shown on the display. Make sure
that the A.M. / P.M. setting is correct.
Money
Fan
Timer Operation
Set Hr.
Stop
Start
Temperature
Fan
Cool
On/Off
Power
Cooler
Only
Speed
Saver
®
Warmer
8
10
7
11
9
4
3
1
2
5
6
Figure 4
Low
Cool
High
Cool
Low
Heat
High
Heat
MAX
COOL
MAX
HEAT
Fan
Only
Off
Allow 3 min. between restarts
!
How to operate your Friedrich room air conditioner
(YQ07 / EQ08 models)
Model YQ07
This model is designed for use in warmer climates; therefore it does not have
back-up electric heat and will not provide adequate heating below an outdoor
ambient temperature of 37°F (3° C).
Function control
The left knob is a six position control that allows you to select heat or cool in
either low speed or high speed. Plus you can select fan only if you wish.
Temperature control
-
r
e
t
n
u
o
c
,r
e
l
o
o
c
r
o
f
e
s
i
w
k
c
o
l
c
ti
n
r
u
t
-
t
a
t
s
o
m
r
e
h
t
e
h
t
s
i
b
o
n
k
d
n
a
h
t
h
g
i
r
e
h
T
.
)
5
e
r
u
g
i
F
e
e
S
(
r
e
m
r
a
w
r
o
f
e
s
i
w
k
c
o
l
c
Figure 5
Additional RC1 wireless remote controls can be purchased from your Friedrich dealer.
