Frick HPS 36, Руководство по установке

Страница: 28 / 54

HPS Rotary Screw Compressor Units 070.700-IOM (MAR 21)
Page 28 Operation
Description Display
name
Min. Max. Factory
setting
Unit Comments
Gray shading indicates standard setting
ICM OD
(Opening Degree)
- 0 100 - %
ICM valve Opening Degree is displayed during normal operation.
Running display value (see j01 , j05 ).
Main switch j01 1 2 1 -
Internal main switch
1: Normal operation
2: Manual operation. Valve opening degree flashes. With the down ar -
row and the up arrow push buttons the OD can be entered manually.
Mode jo2 1 2 1 -
Operation mode
1: Modulating - ICM positioning according to Analogue input (see j03)
2: ON/OFF - operating the ICM valve like an ON/OFF solenoid valve
controlled through Digital Input. See also j09 .
Analog input signal j03 1 4 2 -
Type of Analog input signal from external controller
1: 0 mA to 20 mA
2: 4 mA to 20 mA
3: 0 V to 10 V
4: 2 V to 10V
Speed at ON/OFF
and modulating
mode
j04 1 100 100 %
Speed can be decreased. Max. speed is 100 %
Not active when j01 = 2
If j02 = 2, the display indicates speed in display. Low , Med
,
and High
also means ON/OFF operation.
If j04 < = 33, Low is displayed
33 < If j04 < = 66, Med is displayed
If j04 > = 67, High is displayed
Automatic calibration j05 0 1 0 -
Not active before j26 has been operated.
Always auto reset to 0.
CA flashes in the display during calibration.
Analog output signal j06 0 2 2 -
Type of A0 signal for ICM valve position
0: No signal
1: 0 mA to 20 mA
2: 4 mA to 20 mA
Fail-safe j07 1 4 1 -
Define condition at power cut when fail-safe is installed.
1: Close valve
2: Open valve
3: Maintain valve position
4: Go to OD given by j12
Digital input function j09 1 2 1
Define function when Dl is ON (short circuited Dl terminals) when j02 = 2
1: Open ICM valve (Dl = OFF = > Close ICM valve)
2: Close ICM valve (Dl = OFF = > Open ICM valve)
Password j10 0 199 0 -
Enter number to access password protected parameters:
j26
Old alarms j11 A1 A99 - -
Old alarms are listed with the latest shown first. Alarm list can be
reset by means of activating down arrow and up arrow at the same
time for 2 seconds.
OD at powercut j12 0 100 50 -
Only active if j07 = 4
If fail-safe supply is connected and powercut occurs, ICM goes to
entered OD.
ICM configuration j26 0 6 0
NB : Password protected. Password = 11
At first start-up, A1 flashes in display. Enter valve type.
0: No valve selected. Alarm A1 becomes active.
1: ICM20 with ICAD 600
2: ICM25 with ICAD 600
3: ICM32 with ICAD 600
You must get number off Valve Body
4: ICM40 with ICAD 900
5: ICM50 with ICAD 900
6: ICM65 with ICAD 900
OD% j50 0 100 - % ICM valve Opening Degree is displayed during normal operation.
AI [mA] j51 0 20 - mA Analog input signal
AI [V] j52 0 10 - V Analog input signal
AO [mA] j53 0 20 - mA Analog output signal
Digital Input function j54 0 1 - - Digital Input signal
DO Close j55 0 1 - - Digital Output Closed status. ON when OD < 3%
DO Open j56 0 1 - - Digital Output Open status. ON when OD > 97%
DO Alarm j57 0 1 - - Digital Output alarm status. ON when an alarm is detected
MAS mP SW ver. j58 0 100 - - Software version for main microprocessor
SLA mP SW ver. j59 0 100 - - Software version for subordinate microprocessor
Table 9: Parameter list
}