APCO Dual systems (Standard, RT, Mag) include a second,
remote mounted UV light for additional HVAC disinfection,
usually at the coil. Dual systems include a second power
supply for the remote UV lamp. To add a second UV light to
an APCO system that is not a dual purchase an additional UV
light with its own power supply.
Remote UV Light Installation (Dual Systems)
IMPORTANT!
• APCO Dual lamps are wired in series - both must be
connected for lamps to light
• Only qualified technicians should install this product
• Install in accordance with relevant building codes
• Read instructions carefully including safety warnings
WARNING
PROTECT EYES FROM UV LIGHT
TURN OFF UNIT OR DISCONNECT
BEFORE SERVICING
Important:
some materials inside
the air system (including filter
media, flex duct, wiring etc.) may
not be UV light resistant. Use the
optional UV shield (part #TUV-
SHIELD-LPC) or cover the materials
with reflective tape.
Typical remote UV locations
Manufacturer’s Warranty:
This warranty supersedes and replaces any warranty statements orally made by the Sales Person, Distributor or Dealer or contained in the written instructions or other
Brochures or informational documents in relation to this product. This warranty gives you specific legal rights, and you may also have other rights which vary from State
to State.
What Does This Warranty Cover?
This lifetime limited manufacturer warranty covers any defects or malfunctions in material and workmanship under the normal use
and service when operated and maintained in strict accordance with manufacturer’s instructions for the Lifetime of the equipment.
How Long Does The Coverage Last?
1) Power Supply: For as long as you own the real property where the product is installed. 2) TUVL-1XX Series Ultraviolet Lamp
is warranted for germicidal output for one-year from the date of installation. 3) TUVL-2XX Series Ultraviolet Lamp is warranted for germicidal output for two (2) years
from the date of installation. This warranty is not transferable.
What Will Triatomic Environmental, Inc. Do?
Triatomic Environmental, Inc. will replace any defective or malfunctioning part at no charge. You must pay any labor
charges and shipping charges of defective product to our warranty department.
What Does This Warranty Not Cover?
THIS PRODUCT IS NOT INTENDED TO BE PURCHASED AND INSTALLED BY UNLICENSED HVAC OR ELECTRICAL CONTRACTORS. This
warranty does not cover products or parts purchased from any source other than licensed HVAC or electrical contractors. This warranty does not cover parts installed
by unlicensed HVAC or electrical contractors. This warranty does not cover parts damaged as a result of misuse, abuse, or any use other than its intended use, accident,
acts of god, neglect, or from improper operation, maintenance, installation, modification or adjustments. Triatomic Environmental, Inc. shall have no responsibility for
charges incurred by the customer for installation or removal of warranted items.
This warranty does not cover parts or equipment used with the Fresh-Aire UV system that are not manufactured by Triatomic Environmental, Inc.
**This warranty shall be void if UV lamps from manufacturer’s other than Triatomic Environmental, Inc. are used with this equipment.
Consequential and incidental damages are not recoverable under this warranty. Manufacturer assumes no liability for any harm, which may occur as a result of the
use of the equipment herein and shall not be liable for consequential or any other damages whether or not caused by manufacturer’s negligence or resulting from
any express or implied warranty or breach thereof. Consequential damages for the purpose of this warranty shall include, but not be limited to, loss of use, income or
profit, or loss of or damages to property or injury or death to persons or animals occasioned by or arising out of operation, use, the operation, installation, repair or
replacement of the equipment or otherwise. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
There are no Warranties which extend beyond the description of the face hereof.
How Do You Get Service?
In order to be eligible for service under this warranty you MUST return the warranty registration card or register online at www.freshaireuv.
com. If something is wrong with your product, call your installing contractor to receive a Return Merchandise Authorization (RMA) and instructions for returning the
product to a licensed distributor in your area or the manufacturer.
Once the product is returned, we will inspect your product and contact you within 10 business days of our receipt of the product to give the results of our inspection. If
we determine that the product is covered under this warranty, we will ship to you at no additional cost a replacement part. Replacement parts may be refurbished. If we
determine that the product is not covered under this warranty, or that this warranty is void, the product will be returned to you COD. There is no charge for inspection.
How Does State Law Apply?
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
1. Determine the optimal position
for placement of the UV lamp.
2. Use a utility knife to cut a slit in the insulation
on the interior surface.
3. Place the magnetic “Z” bracket directly on
the metal surface or remove the magnet and
hard-mount the bracket using the self-tapping
screws provided. Use foil tape to close the cut in
the insulation.
4. Use plastic quick-nuts to attach the
UV lamp to the “Z” bracket as shown.
STEP 1: Remote UV Surface Installation
STEP 2: Coil “A” plate or Duct Installation
1. Snap the “Z” bracket apart by
bending.
2. Drill a 1” hole in the "A"-plate
or duct then attach the smaller
piece of the bracket using the
self-tapping screws.
3. Insert the UV lamp into the hole
then use the plastic quick-nuts
to attach the UV lamp to the “Z”
bracket as shown.
1.
2.
1.
2.
3.
4.
3.
Z
APCO Standard has an internal power
supply for the second lamp. APCO RT
& MAG have external power supplies
with a cable for the second lamp.
STEP 4 : Remote UV Configuration
1. Find a suitable location on the outside of the duct-work
near the UV Lamp installation and apply the Fresh-Aire UV®
warning/lamp replacement sticker
2. Drill a ½” hole through the orange circle on the sticker. Press
the UV safety viewport into hole.
3. Connect lamp: make sure the flanges are aligned and then
push the connectors firmly together. A tight connection
ensures a proper water-resistant seal.
4. Turn on the power and use the sight glass to confirm that the
UV Lamp is operating.
3.
2.
Align Flanges
Lamp Replacement
Germicidal UV lamps need to be replaced
periodically. Systems will include one-year
(TUVL-1xx), or two-year (TUVL-2xx) UV-C lamps.
Note: UV lamps will continue to emit visible
light but they lose germicidal effectiveness
over time. One-year and two-year lamps are
interchangeable, you can upgrade to a two-year
lamp with your existing power supply.
CAUTION!
UV lamps contain small amounts of mercury
- dispose of lamps in accordance with local
environmental regulations.
For more information visit www.lamprecycle.org
Note: Use of replacement UV lamps other than
Fresh-Aire UV® voids warranty
.
PART: TUVL-115 LIFE: 1 Year
FITS: APCO Standard
PART: TUVL-215 LIFE: 2 Year
FITS: APCO Standard
PART: TUVL-111 LIFE: 1 Year
FITS: APCO RT
PART: TUVL-211 LIFE: 2 Year
FITS: APCO RT
PART: TUVL-115P LIFE: 1 Year
FITS: APCO MAG15, Remote UV Light (dual models)
PART: TUVL-215P LIFE: 2 Year
FITS: APCO MAG15, Remote UV Light (dual models)
PART: TUVL-111P LIFE: 1 Year
FITS: APCO MAG11
PART: TUVL-115 LIFE: 2 Year
FITS: APCO MAG11
