Fresenius Medical Care GranuFlo 450368-03 Скачать руководство пользователя страница 9

Страница: 9 / 67

P/N 450368-03 Rev. E

ECTION

PECIFICATIONS

NSTALLATION

EQUIREMENTS

Prior to operating the Fresenius Medical Care GranuFlo Dissolution Unit II: 99 Gallons (375 Liters), adequate

power and water connections must be made. The GranuFlo Dissolution Unit II is a computer-controlled

electro-mechanical device. The GranuFlo Dissolution Unit II must be installed in an appropriate environment

(indoors) free from extremes of temperature and humidity, free of the presence of flammable anesthetics,

reasonably protected from dust and dirt contamination, liquid splashes, bright sunlight or high intensity

lighting.

Failure to install the GranuFlo Dissolution Unit II according to these guidelines may result in improper

operation or early failure of the device or its components. Direct sunlight may cause discoloration of the

polyethylene tank, lid, or electronic housing.

The GranuFlo Dissolution Unit II needs to be set up using the following parameters:

A 15 amp

GFI

duplex outlet is required. The GranuFlo Dissolution Unit II requires 120 VAC, 60 Hz,

single phase power. The GranuFlo Dissolution Unit II uses approximately 9 amperes total. Electrical

service should meet all applicable national, state and local code requirements.

The electrical power cord, input water hose, and output drain hose shall be properly routed away

from high traffic areas and installed in such a way that does not cause any electrical or safety hazards.

The treated water source must meet

ANSI/AAMI

ISO

requirements for water for hemodialysis,

currently

ANSI/AMMI RD62

, or

ISO 13959

. Plumbing service must meet all national, state and local

plumbing codes. The GranuFlo Dissolution Unit II uses approximately 99 gallons (375 liters) of water

per batch of product.

WARNING!

DO NOT PERMANENTLY INSTALL

RANSFER

OSE TO A STORAGE TANK

CONTAINER

Supply Water Treatment System should be capable of a minimum flow rate of ½ gallon per minute.

The maximum input water pressure is 60psi.

The water temperature should be 20°-30°C (68°-86°F) for dissolution mixing conditions.

Height from the floor to the top of the GranuFlo Dissolution Unit II is approximately 56 inches.

Platform for the GranuFlo Dissolution Unit II is 50 inches long by 28 inches wide.

Transfer Filter Housing is equipped with a ¾” hose barb fitting.

There is a ¾” hose barb inlet fitting, and another for the drain outlet.

10.

The GranuFlo Dissolution Unit II must be level.

11.

The GranuFlo Dissolution Unit II weight is 200 lbs. empty and 1025 lbs. filled.



CAUTION!

HE FLOOR MUST BE CAPABLE OF WITHSTANDING THE MAXIMUM WEIGHT OF

1025

POUNDS

A floor drain emptying into a sewer line must be in the immediate area of the GranuFlo Dissolution Unit II.

NOTE:

RANU

ISSOLUTION

NIT

ANK IS MADE OF NON

FERROUS MATERIAL

Содержание GranuFlo 450368-03




































































Результаты поиска

Содержание GranuFlo 450368-03

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care GranuFlo 450368-03, Руководство оператора

Результаты поиска

Содержание GranuFlo 450368-03

Отзывы:

Бренды по названию

Популярные бренды