Fresenius Medical Care GranuFlo 450368-03 Скачать руководство пользователя страница 32

Страница: 32 / 67

M A I N T E N A N C E Continued

P/N 450368-03 Rev. E

8.4.

NIT

ILTER AND

ASE

TAND

IPE

ILTER

AINTENANCE

The 1-micron filter (FMCNA, P/N

G84-202-12)

should be changed under the following conditions:

1. The filter should be changed after mixing 6 batches.

2. When the GranuFlo Dissolution Unit II requires disinfection.

8.4.1

ILTER

EMOVAL

EPLACEMENT

Ensure the Mixing Tank is empty and that power to the GranuFlo Dissolution Unit II is OFF and the Main

Transfer Ball Valve is CLOSED. Follow steps A, B, C, and D for removal and replacement of the filter (Figure

19). If the residual fluid in the Filter housing is concentrate, then place the solution in the

Residual

Solution Bucket.

Figure 19

8.4.2.

ASE

TAND

IPE

ILTER

EMOVAL

Using Base Filter Rod, P/N 260025 (Figure 20A), reach into the tank and connect the small end of the

shaft into the Screw Nut of Base Filter (Figure 20B). Turn the Screw Nut Counter Clockwise until the Base

Stand Pipe Filter is no longer attached to the tank. Use the Base Filter Rod to help lift the Base Stand Pipe

Filter out of Tank. Thoroughly clean off the top of the Pie Plate Filter holes by running purified water over

the filter holes until all debris is removed. Once the Pie Plate Filter is clean reinstall the Base Stand Pipe

Filter.

IGURE

NOTE:

HE FILTER USED MUST BE COMPATIBLE WITH

RESENIUS

EDICAL

ARE

CID

RODUCT AND RATED AT

MICRON

RESENIUS

EDICAL

ARE

G84-202-12,

IS A

OLYPROPYLENE FIBER WOUND ON A POLYPROPYLENE MESH CORE MEETS THESE

REQUIREMENTS

ELLULOSE FILTERS ARE NOT COMPATIBLE WITH THE

RESENIUS

EDICAL

ARE

CID

RODUCT

NOTE:

T IS RECOMMENDED TO REPLACE THE FILTER AFTER MIXING

BATCHES OR IF THE TANK REQUIRES DISINFECTION

A. Close Main Transfer Ball Valve

and Remove Filter Housing

C. Insert Filter

(P/N G84-202-12)

D. Install Filter Housing onto

the filter holder.

B. Remove Filte

A. P/N 260025, Base Filter Rod

B. Base Stand Pipe Filter Removal

Figure 20

Содержание GranuFlo 450368-03




































































Результаты поиска

Содержание GranuFlo 450368-03

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care GranuFlo 450368-03, Руководство оператора

Результаты поиска

Содержание GranuFlo 450368-03

Отзывы:

Бренды по названию

Популярные бренды