Fresenius Kabi OPTIMA PT-VS-S Скачать руководство пользователя страница 98

Страница: 98 / 106

optima07.1_001b_en.fm

libr

ati

Calibrating the downstream pressure sensor at 0 mm Hg with the door closed, filled

tube installed.

Position the tube according to the preceding diagram and
open the 3-channel tap in the direction of the Pump-
Manometer.

Press "START", to warm up the tube.

Wait until the pressure reaches around 750 mm Hg
(1 bar +/- 0.05 bar), and open the 3-channel tap in the
pump-container direction to lower the pressure
(0 mm Hg).

Press "STOP" to stop infusion.

Press "ENTER" to record the pressure.

The threshold for the "downstream pressure
at 0 mm Hg door closed" should be between
1499 < X < 3696 mV.

Calibrating the downstream pressure sensor at 750 mm Hg with the door closed filled

tube installed.

Position the 3 channel tap in the direction pump-manometer.

Press "START" to start up the pump.

Wait until the pressure reaches 750 mm Hg ±30 mm Hg
(1 bar +/- 0.05 bar).

Press "STOP" to stop infusion.

Press "ENTER" to record the pressure value.

The threshold for "downstream pressure at
750 mm Hg door closed" should be between
898 < X < 2998 mV.

Calibrating the upstream pressure sensor at 0 mm Hg with the door closed filled

tube installed.

Keep the door closed.

Open the 3-channel tap in the direction pump-container.

Press "ENTER" to record the pressure, when the pressure level

is back to 0 mm Hg.

The threshold for "upstream pressure
at 0 mm Hg door closed" should be between
1499 < X < 3696 mV.

Press "STOP" key to exit the menu without memorising the calibration
values.

Содержание OPTIMA PT-VS-S











































































































Результаты поиска

Содержание OPTIMA PT-VS-S

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Kabi OPTIMA PT-VS-S, Техническое руководство

Результаты поиска

Содержание OPTIMA PT-VS-S

Отзывы:

Бренды по названию

Популярные бренды