Fresenius Kabi OPTIMA PT-VS-S Скачать руководство пользователя страница 3

Страница: 3 / 106

Optima_PT-VS-ST_enTDM.fm

1 Presentation...................................................................................................... 7

1.5.1

Electrical details ......................................................................................................... 9

1.5.2

Electronic details ........................................................................................................ 9

1.5.3

Mechanical details...................................................................................................... 9

1.5.4

Conformity and norms.............................................................................................. 10

2 Description and operation............................................................................. 11

2.1 Physical description ............................................................................ 11

2.1.1

Display board and front panel .................................................................................. 12

2.1.2

The CPU board ........................................................................................................ 14

2.1.3

The power supply board and battery........................................................................ 17

2.2 Operational description ....................................................................... 19

2.2.1

Tube check and maintenance sub-assembly........................................................... 19

2.2.2

Pumping sub-assembly............................................................................................ 19

2.2.3

External connection sub-assembly .......................................................................... 19

3 Description of the menus .............................................................................. 21

3.1 Parameter configuration menu ........................................................... 21

3.1.1

Access to the menu.................................................................................................. 23

3.1.2

SAV1

, preventive maintenance configuration ....................................................... 24

3.1.3

SAV2

, tube selection configuration ....................................................................... 24

3.1.4

SAV3

, "Beep" ........................................................................................................ 25

3.2 Calibration menu .................................................................................. 27
3.3 After-Sales Service test menu............................................................. 29

4 Preventive maintenance ................................................................................ 31

4.1 Recommendations ............................................................................... 31
4.2 Maintenance schedule ......................................................................... 31

4.2.1

Preventive maintenance........................................................................................... 31

4.2.2

Quality control .......................................................................................................... 31

4.3 Checks................................................................................................... 33

4.3.1

Accessing the tests .................................................................................................. 33

4.3.2

Visual check ............................................................................................................. 33

4.3.3

Operating period and maintenance date.................................................................. 34

4.3.4

Indicator lights test ................................................................................................... 34

4.3.5

Keyboard check ....................................................................................................... 35

4.3.6

Battery voltage check............................................................................................... 35

4.3.7

Checking the last 10 alarms..................................................................................... 35

Содержание OPTIMA PT-VS-S











































































































Результаты поиска

Содержание OPTIMA PT-VS-S

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Kabi OPTIMA PT-VS-S, Техническое руководство

Результаты поиска

Содержание OPTIMA PT-VS-S

Отзывы:

Бренды по названию

Популярные бренды