INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
TREADMILL
OPERA
TION
LIMITED
W
ARRANTY
TROUBLESHOOTING
&
MAINTENANCE
CONDITIONING
GUIDELINES
INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE YOU
BEGIN
TREADMILL OPERA
TION
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
PRE-ASSEMBLY
ASSEMBLY
STEP 1
FLAT WASHER (B)
20 mm
Qty: 1
WAVY WASHER (F)
29 mm
Qty: 1
BOLT (D)
Qty: 1
BOLT (A)
15 mm
Qty: 1
TEFLON WASHER (C)
18 mm
Qty: 1
FLAT WASHER (E)
27 mm
Qty: 1
HARDWARE BAG 1 CONTENTS :
TEFLON WASHER
(C)
ELEVATION FRAME
FLAT WASHER
(B)
BOLT (A)
WAVY WASHER (F)
FLAT WASHER (E)
LEFT CONSOLE MAST
BOLT (D)
MAIN FRAME
LEFT LINKAGE ARM
Open
HARDWARE BAG 1
.
Cut banding straps. Do not move or lift treadmill from packaging.
Move
LEFT LINKAGE ARM
into position. Insert 1
BOLT (A)
and 1
FLAT WASHER (B)
into
LEFT
LINKAGE ARM
followed by 1
TEFLON WASHER (C)
and attach to
ELEVATION FRAME
.
Lift
LEFT CONSOLE MAST
into upright position. Be sure to hold the console mast firmly, as
it will not stay in the upright position on its own.
Insert 1
BOLT (D)
and 1
FLAT WASHER (E)
through
LEFT CONSOLE MAST
followed by
1
WAVY WASHER (F)
and attach to
MAIN FRAME.
A
B
C
D
E
ASSEMBLY
STEP 2
ELEVATION FRAME
BOLT (D)
RIGHT LINKAGE ARM
FLAT WASHER (E)
MAIN FRAME
RIGHT CONSOLE MAST
CONSOLE CABLES
PRE-ATTACHED BOLT
WAVY WASHER (F)
WAVY WASHER (F)
29 mm
Qty: 1
BOLT (D)
Qty: 1
FLAT WASHER (E)
27 mm
Qty: 1
HARDWARE BAG 2 CONTENTS :
1
3
2
NOTE:
If you have attempted to
move the treadmill from the box
and the machine has sprung
open and cannot be assembled,
refer to the troubleshooting
section in order to restore the
treadmill to its proper position.
*
RIGHT CONSOLE MAST
LEAD WIRE
CONSOLE CABLES
Pull
LEAD WIRE
through
RIGHT CONSOLE MAST
. After
pulling the
LEAD WIRE
through the mast, the top of the
CONSOLE CABLE
should be located at the top of the
mast. Detach and discard
LEAD WIRE
.
Open
HARDWARE BAG 2
.
Move
RIGHT LINKAGE ARM
into position and attach to
ELEVATION FRAME
.
NOTE: While holding
RIGHT CONSOLE MAST
in the
upright position, tighten
PRE-ATTACHED BOLT
using
T-wrench to attach
RIGHT LINKAGE ARM
.
Insert 1
BOLT (D)
and 1
FLAT WASHER (E)
through
RIGHT CONSOLE MAST
followed by 1
WAVY WASHER (F)
and attach to
MAIN FRAME.
Lift the
RUNNING DECK
until lock latch on side of
treadmill is fully engaged.
Remove
CONSOLE
from box and place out of the way.
Lower the treadmill
RUNNING
DECK
from the folded
position by stepping on
LOCK LATCH
on lower right side.
A
B
C
D
E
F
G
DO NOT ATTEMPT TO LIFT THE TREADMILL!*
Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. Failure to do
so may result in injury! Remove plastic wrap from console masts.
NOTE:
During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware.
Any grease, such as lithium bike grease is recommended.
WARNING
30727_Rev.1.1.indd 8-9
7/3/07 8:38:14 AM
