Freescale Semiconductor P&E Tracelink Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 39

Freescale Semiconductor P&E Tracelink Скачать руководство пользователя страница 6

Tracelink User Manual

3

2

QUICK START GUIDE

Step 1. Install Software

The accompanying software includes all necessary drivers and configuration utilities
needed for the Tracelink. After installation is complete, make sure the PC is rebooted
before moving on to the configuration step.

Step 2. Power On Tracelink

Power up the Tracelink by connecting the included 9V power supply. A blue LED will
be illuminated on the Tracelink to indicate it is receiving power.

Step 3. Ethernet Configuration

Connect the Tracelink to the PC using a USB connection. Run the ConfigureIP
software utility to set up the network parameters (IP address, subnet mask, etc.). The
Ethernet port will not function properly until this one-time configuration is complete.
You may wish to refer to

Section 5 - ETHERNET CONFIGURATION

. If the Tracelink

Ethernet connection is not required, this step may be skipped.

Step 4. Hardware Setup

Connect the appropriate ribbon cable between the Tracelink and the target board. The
Tracelink case flips open for easy access to the ribbon cable connectors. Power up
the target board. A yellow LED on the Tracelink will be illuminated to indicate that it is
detecting target power.
Finally, connect the USB or Ethernet cable from the Tracelink to the host PC.

Step 5. Launch PC Software

The Tracelink is now ready to be used with PC software to debug and analyze trace.
Please refer to the documentation from the software vendor (e.g., P&E software,
Freescale

TM

CodeWarrior) for more details on any additional configuration that may be

required.

«
...
4
5
6
7
8
...
»

Содержание P&E Tracelink








































Отзывы:

Нет отзывов