Freescale Semiconductor P&E Tracelink Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 39

Freescale Semiconductor P&E Tracelink Скачать руководство пользователя страница 10

Tracelink User Manual

7

3.4.1

PORT A: Kinetis (Mini-10)

Figure 3-5: Port A Pinout

Table C-1. Kinetis Mini-10 Signals (PORT A)

Signal

Direction

Description

TVCC

Input

Target reference voltage. Needs to be con-
nected to the microprocessor’s operating volt-
age (1.8V to 5V) and is used by the Tracelink
to determine the correct voltage level to use on
output signals.

Required.

TMS/

SWD_DIO

I/O

Debug communication signal. Pull-up resistor
required.

Required.

GND

Input

Ground signal. Connect to the digital ground
signal of the microprocessor.

Required.

TCK/

SWD_CLK

Output

Debug communication signal. Pull-down resis-
tor required.

Required.

TDO

Input

Debug communication signal. Pull-up resistor
recommended.

Recommended.

TDI

Output

Debug communication signal. Pull-up resistor
required.

Recommended.

RESET

I/O

Microprocessor reset signal. This signal is
driven low during initial debug mode entry. Pull-
up resistor required.

Required.

«
...
8
9
10
11
12
...
»

Содержание P&E Tracelink








































Отзывы:

Нет отзывов