FRC TCA200 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 32

FRC TCA200 Скачать руководство пользователя страница 6

TCA200 Rev171031

6

GENERAL DESCRIPTION

All controls and indicators are located on the front of the control module.

Components

The pressure governor and instrument panel consist of the following components:
Control Module
Intake Pressure Sensor
Discharge Pressure Sensor
Audible Alarm Buzzer
Cables

Control Module

The control module is waterproof and takes up 7 1/2 by 6 inches of panel space. All

controls, indicators, and displays are located on the front of the control panel. (Refer

to Controls and Indicators.)

Intake Pressure Sensor

The pressure sensor is mounted on the pump intake manifold. It provides an input

signal to the control module that is proportional to the intake pressure.

Discharge Pressure Sensor

The pressure sensor is mounted on the pump discharge manifold. It provides an

input signal to the control module that is proportional to the discharge pressure.

Audible Alarm Buzzer

A ground is provided at the 8-pin connector pin 2 to activate the buzzer (max

current: 300mA).

«
...
4
5
6
7
8
...
»

Содержание TCA200

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды