FRC TCA200 Скачать руководство пользователя страница 21

Страница: 21 / 32

TCA200 Rev171031

5. Press the

INC

button.

Result:

P 4

flashes in the

PUMP INTAKE

display. The message display shows

SET

TIME 10:30AM

6. To Change the Time: (If not go to step 7.)

a. Press the

button.

Result:

P 4

stops flashing. The message display shows the current time with the

flashing.

b. Press the

INC

DEC

button to change

c. Press the

button.

Result: The minute flashes.

d. Press the

INC

DEC

button to change the minutes.

e. Press the

button.

Result: The hour flashes.

f. Press the

INC

DEC

button to change the hours.

g. Press and hold the

SILENCE

button to store new time.

Result:

P 5

flashes in the

PUMP INTAKE

display. The message display shows

WARNING

CODES.

7. Press the

button.

Result:

P501

shows in the

PUMP INTAKE

display and the message display shows

the most recent error or fault code. The date and time that the error or fault code was

recorded scrolls in the message display.

8. Press the

INC

DEC

button to scroll through 20 stored error and fault codes.

Note:

FMI codes are displayed starting at

P521

9. Press and hold the

SILENCE

button.

Results:

P 1

flashes in the

PUMP INTAKE

display.

10. Press the

INC

DEC

button to scroll through the P-codes or press the

SILENCE

button

to exit programming mode.

Содержание TCA200

































Результаты поиска

Содержание TCA200

Отзывы:

Бренды по названию

Популярные бренды

FRC TCA200, Руководство пользователя

Результаты поиска

Содержание TCA200

Отзывы:

Бренды по названию

Популярные бренды