FRC TCA200 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 32

FRC TCA200 Скачать руководство пользователя страница 20

TCA200 Rev171031

20

PROGRAMMING

The following program functions are always available to view and change:
P1 - Software Program Revision Number - Read Only
P2 - Product Manufacturing Date - Read Only
P3 - Set Current Date - Read/Write
P4 - Set Current Time - Read/Write
P5 - Retrieve Fault Codes - Read Only

Access Program Features

Note:

When the program (P) code is flashing in the

PUMP INTAKE

display,

press the

INC

or

DEC

button to scroll through the P-codes or press the

SILENCE

button to exit the programming mode.

1. Press the

SILENCE

button and hold it until the

RPM

display shows four dashes

– – – –

and the message display shows

ENTER---

. Release the button.

Result:

P 1

flashes in the

PUMP INTAKE

display. The message display shows the

program revision number

PROG REV V100.03

.

2. Press the

INC

button.

Result:

P 2

flashes in the

PUMP INTAKE

display. The message display shows the

manufacturing date

MFG DATE 09AUG'07

(ddmmm'yy).

3. Press the

INC

button.

Result:

P 3

flashes in the

PUMP INTAKE

display. The message display shows the

current date

SET DATE 17AUG'07

.

4. To Change the Date: (If not go to step 5.)

a. Press the

MENU

button.

Result:

P 3

stops flashing. The message display shows the current date

with the

year flashing.

b. Press the

INC

or

DEC

button to change the year.

c. Press the

MENU

button.

Result: The month flashes.

d. Press the

INC

or

DEC

button to change the month.

e. Press the

MENU

button.

Result: The day flashes.

f. Press the

INC

or

DEC

button to change the day.

g. Press and hold the

SILENCE

button to store the new date.

Result:

P 4

flashes in the

PUMP INTAKE

display. The message display shows

SET TIME 10:30AM

. Go to step 6.

«
...
18
19
20
21
22
...
»

Содержание TCA200

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды