manualshive.com logo in svg

FRC PumpBoss PBA100, Предварительный документ

Поделиться
Скачать
FRC PumpBoss PBA100 Скачать руководство пользователя страница 7

PBA100 Rev0305PreLim

7

PRELIMINAR

Y

 DOCUMENT

FOR REFERENCE/REVIEW

 ONL

Y

Contol Panel

The control panel is waterproof and takes up 4 5/8 by 6 3/4 inches of panel space.

All controls and indicators are located on the front of the control panel. (Refer to
Controls and Indicators.)

Pressure Sensor

The pressure sensor is mounted on the pump discharge manifold. It provides an

input signal to the control module that is proportional to the discharge pressure.

Engine Coolant Temperature Sensor

The engine coolant temperature sensor is installed as necessary.

Engine Oil Pressure Sensor

The oil pressure sensor is installed as necessary.

Audible Alarm Buzzer (Optional)

The optional buzzer is installed as required.

Transmission Temperature Sensor (Optional)

The optional transmission fluid temperature sensor is installed as required.

Cables

There are two cables that connect to the control module. The 8-pin connector is

for the remote throttle interface, the 12-pin connector is for the monitoring and display
interface.

Содержание PumpBoss PBA100






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды