manualshive.com logo in svg

FRC PumpBoss PBA100, Предварительный документ

Поделиться
Скачать
FRC PumpBoss PBA100 Скачать руководство пользователя страница 4

PBA100 Rev0305PreLim

4

PRELIMINAR

Y

 DOCUMENT

FOR REFERENCE/REVIEW

 ONL

Y

INTRODUCTION

Overview

The Fire Research PumpBoss pressure governor uses state of the art programmable

microprocessor technology and operates in one of two modes, pressure or RPM. It
will maintain a steady pump discharge pressure within system capabilities by controlling
the engine speed. When selected, it will also maintain a selected engine RPM.

In pressure mode the PumpBoss maintains a constant pump discharge pressure.

The discharge pressure is monitored and compared to the selected pressure setting,
the engine RPM is varied to keep the discharge pressure at the selected setting.

In RPM mode the PumpBoss maintains a constant engine RPM. The pump

discharge pressure is monitored, it can vary but will be limited to an increase of 30 PSI.
If the discharge pressure increases 30 PSI, the pressure governor will automatically
lower the engine RPM to reduce the discharge pressure.

All controls and indicators are located on the front of the control module.

Features

J1939 CAN Bus for Engine Information and Control

Power Up in Pressure Mode

Automatic Regulation of  Pump Discharge Pressure

Manual Control of Pressure or Engine RPM Settings

Field Programmable Presets

Diagnostic Capabilities

No Pressure or RPM Variation When Changing Modes

Limits Increase of Pressure When in RPM Mode

Recognition of No Water Condition With Automatic Response

Interlock Signal Recognition with Throttle Ready LED

Return to Engine Idle With the Push of a Button

Automatic Adjusting of LED Displays for Day/Night Viewing

High Idle

Audible Alarm Buzzer (Optional)

Transmission Temperature Sensor (Optional)

KPa (Optional)

Содержание PumpBoss PBA100






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды