IMPORTANT: You will need at least 3 1/2” of solid depth for a sufficient installation. Any shallower than 3” the integrity of
the install may be compromised causing catastrophic failure to your surface, the umbrella and surrounding property. Always
consult a professional before installing.
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
TOP VIEW
Put the Deckplate in place where you intend to mount
your umbrella and mark where you need to drill into
the concrete.
Drill your markings that you’ve marked by wrapping
tape on your drill bit.
(See TIP)
Drop your wedge anchors in (hammer in if-needed),
and torque down all four bolts.
Mount your Spigot to the inner four threaded holes
exposed by removing the grub-screws.
It is normal for the washer
to rest on the ledge of the
counter-sunk hole or above
and overlapping.
SPIGOT
DECK PLATE
Your Aurora Cantilever comes with the Spigot already inserted in the mast of your umbrella. Once you have properly installed your Deck Plate,
remove the Spigot from your umbrella and you can begin to mount your Spigot to the Deck Plate, and then the umbrella. (see
FIGURE 4
).
TOOLS & MATERIALS NEEDED
•
(x4) 1/2” x 3 3/4” Concrete Wedge Bolts (Longer can be used) - Min. length of 3” if applicable.
•
1/2” Open ended or box wrench (Torque Wrench is optimal)
•
Hammer Drill / 1/2” x 4” Carbide mason hammer drill bit 4” +
•
1/2” Open ended or box wrench.
•
Hammer
•
Can of Air / Air Compressor
•
Marker/Paint to mark drill point on surface
IMPORTANT:
Minimum recommended anchored depth should be no less than 3”. We highly recommend there being at least a depth of
3.5” on any concrete or solid surface to anchor your umbrella into.
•
Level
1. Unpack your Deck Plate and place onto the position you plan on installing your cantilever umbrella. Using a marker or spray paint,
mark through the bolting pattern (
FIGURE 1 :magenta:
) onto the concrete.
2. Now that your marks are in place, measure the depth you intend to drill on the drill bit and add at least 1/2” to the depth and mark with
a piece of masking tape around the drill bit (min. 3” + 1/2”). (
FIGURE 2
)
3. Set your Deck Plate back in place over the holes you have just drilled. Drop your wedge or sleeve anchors in, and if needed, use a
hammer to pound the anchors fully down and into the Deck Plate. The washers should nestle nicely into the edge of the countersunk
hole, or overlap the countersunk hole. Either is perfectly fine and will not compromise the installation (
FIGURE 3
).
4. Using your 1/2” wrench or a drill, torque down the anchors to 55 lbs. (74Nm) of torque wrench is available (
FIGURE 3
).
5. Now that your Deck Plate is in place and secured, double check that the grub-screws are removed from the inner pattern, retrieve
your Spigot from the mast of your cantilever and set onto the Deck Plate in place over the threaded holes.
6. Using the supplied hardware that is packed with your umbrella, bolt the Spigot onto the Deck Plate (
FIGURE 4
). Once your Spigot is
secure to the Deck Plate, begin to lift the Aurora onto the Spigot until you hear an audible “click” indicating your umbrella is secure.
TIP: BE SURE TO DRILL 1/2” DEEPER THAN THE ANCHOR AND REMOVE DUST FROM THE HOLE THAT WOULD
PREVENT THE ANCHOR FROM COMPLETELY DROPPING IN.
CONCRETE SURFACE INSTALLATION
GRUB-SCREWS ARE IN PLACE TO PROTECT THE THREADED HOLES ON BASES
DURING SHIPPING AND STORAGE. THEY MUST BE REMOVED AND DISCARDED
BEFORE THE INSTALLATION OF ANY UMBRELLA.
AURORA
6MM ALLEN WRENCH
(REMOVE GRUB-SCREWS)
8MM ALLEN WRENCH
(MOUNTING HARDWARE)
21
22
INCLUDED DECK PLATE SPECIFIC MOUNTING HARDWARE
