Framery Q Скачать руководство пользователя страница 4

Страница: 4 / 148

Framery Q (UL) Meeting Maggie

7.2 Install the control panel (optional)........................................................................44

7.3 Install the front glasses........................................................................................ 48

7.4 Install the upper and lower frames...................................................................... 53

7.5 Install the booking system bracket (optional).......................................................55

8 Back frames and glasses......................................................................... 63

8.1 Install the side frames (back)...............................................................................63

8.2 Install the lower frame..........................................................................................66

8.3 Install the back glasses........................................................................................67

8.4 Install the upper frame......................................................................................... 69

9 Install the seals..........................................................................................71

10 Install the cover panels and plates........................................................73

11 Install the electrical equipment.............................................................. 75

11.1 Install the metal box with electrics..................................................................... 75

11.2 Install the DC extension cord............................................................................. 79

11.3 Install the LAN cord (optional)............................................................................82

11.4 Power unit...........................................................................................................83

11.4.1 Install the power unit.............................................................................. 83

11.4.2 Install the floor cover board....................................................................84

11.5 Install the control unit......................................................................................... 86

11.6 Install the control panel cord.............................................................................. 89

11.7 Install the motion detector and light................................................................... 91

12 Install the interior.................................................................................... 95

12.1 Assemble the table.............................................................................................95

12.2 Install the table................................................................................................... 98

12.3 Install the LAN data cartridge (optional)...........................................................101

12.4 Install the power outlet..................................................................................... 102

12.5 Install the carpet and floor grid........................................................................ 108

13 Install the door.......................................................................................110

13.1 Install the floor threshold..................................................................................110

13.2 Install the ceiling threshold...............................................................................112

13.3 Install the door..................................................................................................114

13.4 Install the door handle......................................................................................116

13.4.1 Install the smart lock handle (optional)................................................ 119

14 Install the coat hooks........................................................................... 131

15 Assemble the seats...............................................................................132

16 Install the body covers......................................................................... 133

16.1 Install the roof cover panel...............................................................................133

16.2 Install the bottom body covers......................................................................... 134

Содержание Q





















































































































































Результаты поиска

Содержание Q

Отзывы:

Framery Q, Руководство по установке, Страница: 4 / 148

Результаты поиска

Содержание Q

Отзывы: