background image

16

English

In this menu the MUX output parameters from the central unit can be changed.
•  STANDARD: the modulation standard for the output MUX (DVB-T or DVB-C)
•  MODULATOR FREQUENCY: the modulator output frequency can be set according to the frequency in MHz 

or by channel according to the standard channelling in the different countries.

NOTE: the output MUX are not independent but are linked to other pairs by the following parameters: output 

frequency,  bandwidth  and  output  level.  Therefore,  when  these  parameters  are  changed  In  a  multiplex,  the 

settings of the other mux In the same pair are also Immediately changed. The 2 pairs are divided: MUX1-MUX2 

and MUX3-MUX4.
•  RF LEVEL: to set the output power in dBuV, in the range foreseen by the technical specification (75 - 95 dbuV).
Below are a few parameters relative to the DVB-T modulation standard: 

FEC (1/2 ,2/3, 3/4, 5/6, 7/8), guard interval (1/4,1/8,1/16,1/32), constellation (QPSK,16QAM ad 64QAM), number 

of carriers (8K, 2K), spectrum (normal or inverted). 

The “Alarm overflow” checkbox shows if a band overflow has to be reported to the user by the led on the bottom or not.

NOTE:  Click on “SAVE” to save the changes.

6.7 PROGRAM CONFIGURATION

The CONFIGURATION -> PROGRAMS -> MUX 1 / MUX 2 / MUX 3 / MUX 4  menu allows access to the output 

Multiplex configuration page (Fig 8).

Fig 8

Fig 7

Содержание 3DG-4ASI-4T





























Отзывы: