Foxwell OS100 Скачать руководство пользователя страница 26

Страница: 26 / 95

Foxwell OS100 Digital Oscilloscope User’s Guide_English Version_V1.00

In addition to displaying waveforms, the display area is filled with many details about the

waveform and the oscilloscope control settings.
1.

The Main Menu:

All settings can be found in the main menu.

The Toolbar

Displays the trigger information:

Displays the edge trigger slope, source and level.

The Horizontal Panel:

The user can change Time/Div, format in the panel.

The Vertical Panel:

The user can turn on/off the CH1/CH2/CH3/CH4. Also the user can

change the CH1/ CH2/CH3/CH4 volt/div, coupling and probe attenuation.

The Trigger Panel:

In this panel, the user can change the trigger mode, sweep, source and

slope.

Displays the system time.

Marker shows Edge trigger level

Displays the main time base setting.

10.

Displays the CH1/CH2/CH3/CH4 information:

Readouts show the coupling of the channels.

Содержание OS100
































































































Результаты поиска

Содержание OS100

Отзывы:

Похожие инструкции для OS100

Бренды по названию

Популярные бренды

Foxwell OS100, Руководство пользователя

Результаты поиска

Содержание OS100

Отзывы:

Похожие инструкции для OS100

Бренды по названию

Популярные бренды