Foxconn 915M07 series Скачать руководство пользователя страница 14

Страница: 14 / 106

Chapter 1 Product Introduction

915M07 Series User Manual

ATX 12V connector

This power connector connects the 4-pin 12 V plug from the ATX 12 V power

supply.

CPU socket

LGA 775 Socket T is for the Intel

Prescott-T processor.

North Bridge controller

Intel

915G/P/GV supports FSB 800/533 MHz, DDR 333/400 MHz, PCI

Express x16 (only for I915G/P). Intel

915G/GV provides an integrated gra-

phics accelerator.

DDR DIMM slots

These four 184-pin DIMM slots support up to 4 GB system memory

using unbuffered non-ECC DDR 333/400 DIMMs.

ATX power connector

This 24-pin connector connects to an ATX power supply. The power supply

must have at least 1 A on the +5 V standby lead (+5 VSB).

Floppy disk connector

This connector accommodates the provided ribbon cable for the floppy disk

drive. One side of the connector is slotted to prevent incorrect insertion of

the floppy disk cable.

IDE connector

The IDE connector supports Ultra DMA 100/66, PIO Modes 3 & 4 IDE device.

The connector is slotted to prevent incorrect insertion of the IDE ribbon cable.

Flash ROM

This 4 Mb flash ROM contains the programmable BIOS program.

Содержание 915M07 series











































































































Результаты поиска

Содержание 915M07 series

Отзывы:

Похожие инструкции для 915M07 series

Бренды по названию

Популярные бренды

Foxconn 915M07 series, Руководство пользователя

Результаты поиска

Содержание 915M07 series

Отзывы:

Похожие инструкции для 915M07 series

Бренды по названию

Популярные бренды