Foxconn 865A01 G series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 124

background image

17

Chapter 2 Installation Instructions

865A01 G/PE User Manual

Memory configurations

You may install 64MB, 128MB, 256MB, 512MB, and 1GB DDR DIMMs into the
DIMM sockets using the memory configurations in this section.

The following is important information on memory configurations:
1. Installing DDR DIMMs other than the recommended configurations may

cause memory sizing errors or system boot failures. Use any of the
recommended configurations in the following table.

2. In dual-channel configurations, install only identical (the same type and

size) DDR DIMMs for each channel.

3. Always install DIMMs with the same CAS latency. For optimum

compatibility, it is recommended that you obtain memory modules
from the same vendor. See the following list of qualified vendors. The
following table lists the PC3200/2700/2100 memory modules that have
been tested and qualified for use with this motherboard.

Note:

1. Use

only

identical DDR DIMM pairs

2. For dual-channel configuration, you may install identical

DIMMS in all four sockets or install identical DIMM pairs
in DIMM1 and DIMM3 (yellow sockets), and identical DIMM
pairs in DIMM2 and DIMM4 (blue sockets).

Mode

Sockets

DIMM1

DIMM2 DIMM3 DIMM4

Single-channel

Dual-channel

Populated

Populated

Populated

Populated

Populated

Populated

Populated

Populated

Populated

Populated

Populated

Populated

x

x

x

x

x

x

x

x

x
x

x
x

x

x

x

x

Populated

Populated

Populated Populated

Populated

x

x

Populated

x

x

Populated

x

Populated

x

x

x

865A01-FOXCONN-V1.3-EN-121603.p65

2004-5-27, 18:02

17

«
...
23
24
25
26
27
...
»

Содержание 865A01 G series





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 865A01 G series

NF796M-H310 Series

Бренд: JETWAY Страницы: 63

EZ-USB HX2LP CY4605

Бренд: Cypress Страницы: 2

Бренд: ST Страницы: 82

Бренд: Supero Страницы: 80

Бренд: EVGA Страницы: 1

Бренд: Advantech Страницы: 5

Бренд: Gigabyte Страницы: 96

Бренд: Gigabyte Страницы: 88

Бренд: A-Trend Страницы: 44

Бренд: MSI Страницы: 445

Бренд: Microchip Technology Страницы: 54

Бренд: ASROCK Страницы: 107

Бренд: A-Trend Страницы: 43

Бренд: ASROCK Страницы: 199

AIROC IFW956810

Бренд: Infineon Страницы: 4

Бренд: Abit Страницы: 96

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды