Foxconn 865A01 G series Скачать руководство пользователя страница 19

Страница: 19 / 124

Chapter 2 Installation Instructions

865A01 G/PE User Manual

CPU

This motherboard accepts Intel socket 478 processors (CPUs) with a front side
bus (FSB) of 400/533/800 MHz Processors with Hyper-Threading technology
are supported.

1. Unlock the socket by pressing the le-

ver sideways, then lift it up to a 90

angle.

2. Align the cut edge to the gap in the

base of the socket. Carefully insert
the CPU into the socket until it fits in
place.

3. When the CPU is in place, press it

firmly on the socket while you push
down the socket lever to secure the
CPU. The lever clicks on the side tab
to indicate that it is locked.

Gap in the base

Installation of CPU

Follow these steps to install the CPU.

Push down the socket
lever to secure the CPU.

Cut edge

Attention:

The CPU pins must be properly aligned with the holes in the
socket, otherwise the CPU may be damaged.

865A01-FOXCONN-V1.3-EN-121603.p65

2004-5-27, 18:02

Содержание 865A01 G series





























































































































Результаты поиска

Содержание 865A01 G series

Отзывы:

Похожие инструкции для 865A01 G series

Бренды по названию

Популярные бренды

Foxconn 865A01 G series, Руководство пользователя

Результаты поиска

Содержание 865A01 G series

Отзывы:

Похожие инструкции для 865A01 G series

Бренды по названию

Популярные бренды