background image

 

15

 
 
 
 

After the control panel has been installed and started, the customer must provide for 
the appropriate elimination/disposal of the waste materials according to the legislation 
locally in force. 
If the control panel or parts of it must be taken out of service and dismantled, follow 
local regulations regarding sorted waste disposal. Refer to the appropriate recycling 

centres. 

CAUTION:

 Contamination of the environment with hazardous substances such as 

battery acid, fuel, oil, plastic, copper, etc., may cause serious damage to the 
environment and endanger people’s health. 
 
 

 
 
 
Our products are guaranteed for a year from the date of commissioning; this applies 
only to products purchased from our offices or from our authorised retailers. The 

warranty does not extend beyond 15 months from the date of shipping. If the 
shipping documentation is missing, the date of manufacture is given in the code on 
the nameplate or fused into the interior of the terminal box. The warranty covers all 
manufacturing defects of material manufactured by us; it covers replacement and 
repair only, at our premises and by our staff, of the defective panel or part. The 

warranty does not provide for any claims by the customer. The warranty does not 
cover damage caused by faulty electrical connections, lack of adequate protection, 
incorrect assembly, incorrect use or any negligence in installing and operating the 
plant. The WARRANTY is also void in the following circumstances: 
- damage due to corrosion or abrasion of any type or nature; 

- malfunction due to improper installation; 
- repair, disassembly or tampering by unauthorised persons; 
- failure by the customer to pay due amounts. 
The defective product must be returned to our factory carriage paid. We reserve the 
sole right to determine the cause of the defect and whether it is covered by the 
warranty or not. After the repair, the goods will be returned to the Customer carriage 

forward. WE DECLINE all liability for damages and injury caused by our products. 
Fourgroup S.r.l. reserves the right to modify its products without notifications. Any 
controversy arising from the terms of this warranty shall be resolved in the Padua 
Court, even if payment is agreed by bank’s draft. 
For any further information, refer to the sales contract. 

 
 
 
 
 

Always state the exact model identification number and construction number when 
requesting technical information or spare parts from our sales and service centre. 
 
 

Use only original spare parts when replacing any faulty components. 

 

 

The use of unsuitable spare parts can cause malfunctions, personal injury 

 

and damage to property. 

 

13. WASTE DISPOSAL 

14. WARRANTY 

15. SPARE PARTS 

 

 

Содержание Simplex-Up





















Отзывы: