background image

Warranty Information

This warranty is valid for the original consumer purchaser only and excludes industrial, 

commercial or business use of the product, product damage due to shipment or failure which 

results from alteration, product abuse, or product misuse, whether performed by a contractor, 

service company, or consumer. We will not be responsible for labor charges and / or damage 

incurred in installation, repair or replacement, nor for incidental or consequential damage.

The appliance has been manufactured under the highest standards of quality and workmanship. 

We warrant to the original consumer purchaser that all aspects of this product will be free of 

defects in material and workmanship for one year from the date of purchase. A replacement 

for any defective part will be supplied free of charge for installation by the consumer. Defects 

or damage caused by the use of other than genuine parts are not covered by this warranty.

This warranty shall be effective from the date of purchase as shown in the purchaser’s receipt.

Need help?

call our toll free number at:

1-866-814-0585 or

e-mail:

 

[email protected]

25

Содержание 227770


























Отзывы: