Forum 691250-Z-BC Скачать руководство пользователя страница 29

Страница: 29 / 66

Operation Maintenance Manual

07-2018

PN 691250-Z-BC-D - Revision: 04

Solid Body Elevator

RT/

STA

3.2

Transport

DANGER

Suspended load!

The falling load can cause severe, even
lethal injuries.

» NEVER stand beneath or in the

swing area of lifted loads or loads
suspended from a crane.

WEAR PROTECTIVE HELMET!

WEAR PROTECTIVE GLOVES!

WEAR SAFETY SHOES!

INFO

Safe Lifting Points !

- Lifting point locations, especially bores for

load hooks are marked on the Bushing
segments.

• Make Sure all load hooks are fully installed in

the lifting point

» Thus, the safe transport of

FORUM Handling Tools

equipment is

ensured.

INFO

Internal transport on site!

• It is advised to use pallets for longer

component transports.

» Use a pallet for transport.

Detailed weight specifications are given in the
Chapter „1.3 Technical Data“ on page 8.

Principles for transport

1. Ensure that transport routes are sufficiently

dimensioned.

2. Always use pallets for longer transport distances.
3. The total weight (object to be trans means

of transport, e.g. forklift) must not exceed the
supporting capacity of the subsurface.

4. Ensure that such work is performed only by

sufficiently qualified personnel.

5. Ensure that visual and audio contact exists between

the crane operator and operating personnel.

6. Secure the area against unauthorized entry. If

necessary mark the area with information signs to
warn of maintenance and repair work.

7. Secure moving parts in suitable manner.
8. Use only approved slinging and transport

equipment, which is in perfect condition and
suitable for the intended purpose. Observe specified
load limits.

9. Secure to be equipment against slipping/sliding.

Observe equipment weight. Observe center of
gravity.

10. Never stand under suspended loads.
11. Transport the equipment carefully. Do not fasten, lift

or pull equipment on parts, that could be damaged.
Avoid sudden stops.

12. Always use hoisting equipment (slings, hoisting

cables, shackles, etc.), which has been inspected and
is sufficiently dimensioned.

13. Ensure that all installation and hoisting procedures

are accomplished in compliance with recognized
rules of practice and industrial standards.

Содержание 691250-Z-BC



































































Результаты поиска

Содержание 691250-Z-BC

Отзывы:

Похожие инструкции для 691250-Z-BC

Бренды по названию

Популярные бренды

Forum 691250-Z-BC, Руководство по эксплуатации

Результаты поиска

Содержание 691250-Z-BC

Отзывы:

Похожие инструкции для 691250-Z-BC

Бренды по названию

Популярные бренды