background image

505 Keystone Rd, Southampton, PA 18966, USA 

(877) 497 6937

.

 [email protected] 

www.fortresspower.com

 

 

•  Recommended terminal torque is 7.0 – 7.7 Nm (5.1 – 5.7 ft-lb) 

•  Power  Cabling  for  the  Fortress  Power  Battery  is  not  included.  System  Wiring  Basics  Refer  to 

published electrical wiring specifications and ratings, refers to the below Battery Cable Sizing Chart. 
Your qualified installer or application specifications will determine the wire gauge for your system. 

 

      CAUTION: Verify polarity at all connections with a standard volt meter before energizing 

the  system.  Reverse  polarity  at  the  battery  terminals  will  void  the  Warranty  and  destroy  the 
batteries. Do not short circuit the batteries.

 

4.5 Connection Terminals   

The Fortress Lithium Batteries are equipped with two M8 threaded terminals with a lock washer and 
nut. The right-hand stud resides in a red high temperature molded insert. This connection is for the 
positive lead. The left-hand stud resides in a black high temperature insert. This connection is for the 
negative lead. 10mm ring terminals along with proper size wiring cables are required to connect battery 
to inverter/charger. Do not reverse polarity, doing so will void warranty. Use a volt meter to check polarity 
before connecting terminals.   

Water Resistant Plastic Terminal Covers are also included and will be in place when your units arrive. 
The boots are to be placed over the cable terminations and will stretch to form a water-resistant seal 
around the base of the molded inserts and terminal connections. 

NOTE! Without exception, product experiencing terminal burn out will not be warranted. 

4.6 Mounting Hardware   

The Fortress LFP-5 battery is designed to sit on the floor or mount on the wall. It’s recommended to put 
the Batteries on the wall to avoid flooding or in some cases earthquake vibrations. Please refer to the 
Fortress Lithium Battery Data Sheet for weight and dimension. 

Mounting the battery pack to a wall 

Make sure to leave a space of at last 2.18in (55mm) in between the battery pack and the wall. At least 
5in (127mm) between each unit.

 

 

 

 

 

 

 

 

Содержание LFP-10















Отзывы: