background image

 

 

Thank you for choosing MPP1 Pick & Place Manipulator. 

 

Please read these operating instructions carefully before using the product. The instructions will 

help you become familiar with the product, its installation and proper use as soon as possible. 

Please retain this manual for further reference. 

 

 

Safety instructions

 

Use  the  manipulator  only  for  the  purposes  specified  by  the  manufacturer,  in  accordance  with  the 

operating  instructions  and  warranty.  Read  the  instructions  carefully,  the  manufacturer  is  not 

responsible for damage and injuries caused by improper use. 

Dispose  of  all  packaging  material  and  dispose  of  it  in  an  environmentally  friendly  manner  in 

accordance with local legislation. If you find damage caused by the carrier, do not use the device and 

contact your dealer. 

The  manipulator  is  intended  for  indoor  use  only  and  must  be  placed  on a  flat surface,  on  a  secure, 

stationary structure. Do not install the manipulator in places with excessive dust and humidity. 

For power supply, use a suitable mains plug that complies with your local standards for power supply 

with a 

nominal voltage of 230 V and a frequency of 50Hz. 

Switch-off device is the power plug.

 Power plug must always be accessible in case of an emergency. 

Protect the charger from any physical or mechanical strain, e.g. bending, twisting, binding, shutting to 

the ajar door etc. Take special care to socket-outlets, plugs and the locus of entry of power cord into 

the device. Be careful not to cover vents on the device. The device can overheat itself after prolonged 

use, which can lead to its damage. If you notice any smoke or unusual smell coming from monitor, 

vacuum pump, adapter or electronics cover; 

turn off the device immediately and contact the seller.

 

The  device  can  only  be  moved  when  it  is  switched  off  and  all  cables  are  disconnected.  Use  only 

approved additional devices or accessories approved by the manufacturer.

 

 

 

Observe please national and international regulations for occupational safety and health 

 

 

 

Содержание MPP1

















Отзывы: