Forster TAP0-EZ1-27 Скачать руководство пользователя страница 8

8

Locating the Automatic Feeder

3 Locating the Automatic Feeder

3.1 Local Electrical Connection

:

Refer installation of the local electrical connection to qualified electricians.

:

Observe local recommendations and protective measures. To operate the automatic fee-

der, it is demanded to install a fault--current circuit breaker (30 mA) in the main distribu-

tion frame.

:

The automatic feeder requires its own power supply:

refer to chapter 2, page 7,

„Specifications of the Automatic Feeder“.

:

Observe rated voltage and rated frequency. The supply voltage indicated on the rating

plate of the automatic feeder must correspond to the one of the mains.

:

In case of overvoltage risk, install an overvoltage limiter in the local main distribution

frame.

For animals’ safety and to prevent electrical interferences, carry out an equipotential bon-

ding of all metal parts such as the water line, the feeding station, the race--way and the auto-

matic feeder. At the rear of the automatic feeder is located the connection screw for the

equipotential bonding which has to be connected to an earth circuit connector or to a local

earth electrode by means of a short coupling.

As it is technically impossible to protect the installation against lightning stroke separately,

it is to the owner to install an adequate lightning protection, such as e.g. a lightning protec-

tion system for the entire building. We recommend to conclude a lightning protection insu-

rance.

3.2 Installing the Automatic Feeder

:

The automatic feeder has to be placed in a dry location, if possible, not in the animal

area (e.g. in the fodder storage or similar detached room).

:

A fence of planks protects the automatic feeder against dirt and flies.

:

In order to ensure a good functioning of the feeding process even in case of frost, you

have to equip the automatic feeder with a protection against frost (accessory). The owner

is responsible for a reliable water supply.

:

The suction hoses can be easily guided through a wall.

Equipotential
bonding

Lightning
protection

Содержание TAP0-EZ1-27























Отзывы: