Formax FD 150 Скачать руководство пользователя страница 7

Страница: 7 / 48

Operating Manual

1/97

1.4 Safety

Precautions

Please observe the following safety precautions and
warnings at all times while operating, cleaning or repairing
the

FD 150

. Failure to so may result in physical injury or

damage to the

0. Neither

Formax

nor the

manufacturer assumes any liability for your failure to
comply with these requirements.

WARNING

NEVER CLEAN, CLEAR OR DISASSEMBLE THE

150

WITHOUT FIRST UNPLUGGING THE

POWER CORD.

WARNING

KEEP LOOSE CLOTHING, TIES, SCARVES AND
HAIR AWAY FROM ALL MOVING PARTS.

WARNING

DO NOT PLACE FINGERS BETWEEN OR NEAR
MOVING PARTS.

1.5 Frequently-

Used Terms

leading edge

The edge of the document that
enters and exits the

FD 150

first.

trailing edge

The edge of the document that
enters and exits the

FD 150

last.

imprint position

The point at which the document
is imprinted.

imprint saddle

Contains a plastic relief of the
imprint; 2 imprint saddles are in
the rounded imprint saddle
holder - as one is imprinting, the
other is being inked.

Содержание FD 150

















































Результаты поиска

Содержание FD 150

Отзывы:

Бренды по названию

Популярные бренды

Formax FD 150, Руководство оператора

Результаты поиска

Содержание FD 150

Отзывы:

Бренды по названию

Популярные бренды