manualshive.com logo in svg

Formax FD 150, Руководство оператора

Поделиться
Скачать
Formax FD 150 Скачать руководство пользователя страница 30

Operating Manual

 

26

 

 

1/97

 

6.  Align the two straight RECEIVING TRAY 

MAGNETIC DOCUMENT STOPS with the PAPER 
GUIDES. Center the curved RECEIVING TRAY 
MAGNETIC DOCUMENT STOP so it stops and 
stacks the exiting documents. 

7.  Loosen the FEED ADJUST KNOB and lift up the 

SEPARATOR. 

8.  Place one document, face up in the PAPER GUIDES, 

atop the FEED ROLLS. 

 

 

Documents LONGER than 9” 

Use the following instructions to imprint documents 
longer than approximately 9" (22.86 cm): 
 

• 

If necessary, install the FEED TRAY 
EXTENSION by attaching it to the input end  of 
the 

F

D

 150

 FEED TRAY with the knobs 

provided. 

• 

Feed the top of the document first. 

• 

Install the REVERSE IMPRINT SADDLES. 
Refer to Section 6.1 and follow the instructions 
given for IMPRINT SADDLES. Call your 

Formax

 d

ealer

 to order these saddles. 

 

 

9.   Lower the SEPARATOR against the document and 

tighten the FEED ADJUST KNOB. 

10. Now place a stack of documents up to 1½" high, face 

up in the PAPER GUIDES.  

11. Lower the PAPER WEIGHT to rest on the stack. 
 

 

Содержание FD 150

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды