manualshive.com logo in svg

Formax FD 150, Руководство оператора

Поделиться
Скачать
Formax FD 150 Скачать руководство пользователя страница 32

Operating Manual

 

28

 

 

1/97

 

 

NOTE

 

In order to imprint and count properly, documents 
must feed through the 

F

D

 150

 accurately. If your 

F

D

 150

 does not feed documents straight and with 

a steady rhythm, call your 

Formax

 d

ealer

 for 

service. 

F

D

 150

 feeding components wear with use 

and need periodic replacement. 

 
If multiple documents feed through the 

F

D

 150

, re-adjust 

the gap between the SEPARATOR and the FEED ROLL 
by applying slight downward pressure to the SEPARATOR 
while tightening the FEED ADJUST KNOB. 
 
If the 

F

D

 150

 feeds with difficulty, re-adjust the gap 

between the SEPARATOR and the FEED ROLL by 
tightening the SEPARATOR using the thickness of two 
documents instead of one. If feeding does not improve, 
refer back to section 6.2, 

Loading Documents

. 

 

6.4  Setting     

Imprint Position         
UP / DOWN 

 

 
Use the following instructions to change the imprint 
position toward or away from the leading edge of the 
document. (Refer to 

Figure 6.3

.) 

 

NOTE

 

Always imprint several void or test documents 
until the imprint position is exactly where you 
want it. 

 
1.  Turn POWER SWITCH 

ON

. 

2.  Turn the EXECUTIVE KEY to the 

LOCKED

 position 

and the IMPRINT KEY 

ON

. (Refer to 

Figure 6.1

.) 

 

NOTE

 

Turn the EXECUTIVE KEY 

slowly

. If the SADDLE 

HOLDER does not index, turn the key 

slower

. 

 

Содержание FD 150

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды