background image

 

 

FORM FIT 

HOOD PROTECTOR 

 

   

Scion XD 2010 -   

 

 

 

 

 

 

       

            

 

HD 30D 10

 

Hardware Kit

 

 

Tools Required 

 

4 – Push Type retainers          

6– #6 x 5/8” Flat Head Screws 

1 – Phillips Screwdriver #2 

2 –Metal Brackets 

6 – Clip Bodies 

1 – Tape Measure 

2 – Gasket with Adhesive Tape 

6 – Pins 

 

8 – 3M Anti-Abrasion Film Pad 

6 – ‘L’ Brackets  

5 – Large Bumpons                                       2 – Alcohol Wiping Pads 

   

  

 

Installation      

1

 

 

.  Be sure that the hood is clean and dry inside and out. 

2.  Install the five (5) bumpons as shown. 

Attention: the bumpons must be installed on the hood, not on the deflector!!!

 If the bumpons are installed on 

the deflector, they may wear through the paint.  

NOTE:  

Locate the center of the hood using a tape measure and place the first bumpons as shown in the 

illustration. 

 

205mm 

130mm 

60mm 

430mm           300mm 

 

 

 

 

 

 

3.  Wipe the area where the gasket will be installed with alcohol wiping pad. Measure 70mm from the corner of the hood as shown in the illustration, remove the 

protective liner from the gasket and install the gasket on the surface of the hood. Be sure to install the gasket flush with the leading edge of the hood. Press 
the gasket along its length to ansure a good bond to the surface of the hood. 

 

Attention:

 This product uses a 3M adhesive product that requires installation and curing temperatures of at least 20°C/ 70°F for 24 hours to develop 

maximum adhesion to the surface.  

Failure to install this product at the proper temperature or allow adequate curing time before use is not 

covered under warranty. 

 

 

 
 
 
 
 
 
 
 
 
 
 

 
4.  Open the hood of the vehicle. Peel and fold anti-abrasion film pads in half over the edge of the hood, in the two (2) locations shown.  
 
 

Looking at underside of the hood 

Anti-abrasion Pad and Metal Bracket Locations

 

    

 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание HD 30D 10

Страница 1: ... 3 Wipe the area where the gasket will be installed with alcohol wiping pad Measure 70mm from the corner of the hood as shown in the illustration remove the protective liner from the gasket and install the gasket on the surface of the hood Be sure to install the gasket flush with the leading edge of the hood Press the gasket along its length to ansure a good bond to the surface of the hood Attenti...

Страница 2: ...h of the clips See Illustration Step 8b c Insert a 6 x 5 8 screw through an L bracket and into the clip See Illustration Step 8c 8d d Make sure all the components are well seated together the protector is centered on the hood and then tighten the screws into the clips Clip Configuration Patent No 6 892 427 Step 8b Step 7 Step 8a Step 8c 8d 9 Align the holes in the protector with the holes in the t...

Страница 3: ...qu indiquée dans l illustration 205mm 130mm 60mm 430mm 300mm 3 Essuyez la zone où le joints avec un ruban adhésif sera installé avec de tampon imbibé d alcool Mesere 70mm à partir de coin de la hotte comme le montre l illustration retirez la pellicule protectrice du joint et installer le joint sur la surface de la capot Veillez à installer le joint au ras du bord du capot Appuyez sur le joint sur ...

Страница 4: ...une vis n 6 x 5 8 po au travers du braquet en forme L et dans l agrafe Voir l illustration étape n 8c et n 8d d S assurer que tous les composants sont bien installés sur le capot et serrer les vis dans les agrafes Configuration des agrafes N de brevet 6 892 427 9 Alignez les trous dans le protecteur avec les trous du haut des supports métalliques Assurer le protecteur est bien assis sur la surface...

Отзывы: