A
B
C
R
LISTED
E176225
27700B S.W. Parkway Ave.
Wilsonville, Oregon 97070-9215
1-800-294-6400
www.infocus.com
SP-CEIL-004 DIGITAL PROJECTOR MOUNT
Installation Instructions
These are the installation instructions for your Digital Projector Mount.
Included are four methods of installation. Select the method that works
best for your viewing situation. The methods are:
Fixed Height Ceiling Installation
—
best for short ceilings, eight (8’) or
lower
Adjustable Height Ceiling Installation
—
best for high ceilings, nine (9’)
feet or higher
*
Wall Mount Installation
—
for installing the Digital Projector Mount on a
rear wall
*
If the required height range is greater than 12½", the optional SP-LTMT-
EXTP could be used to extend the length of the suspension adapter (see
(
N)
under “Hardware Description” on the next page). For further
information or ordering assistance, please contact us at the phone
number and address listed at the top of this column.
Before You Start the
Installation
The wall or ceiling where you want to install the digital projector must be
capable of supporting a weight that is five (5) times the weight of 6lbs the
projector you are installing. Consult the projector’s documentation for
weight specifications. If the wall, ceiling, tabletop, shelf, or floor is not
strong enough to handle five (5) times the weight of 6lbs, then you must
reinforce the installation environment. If you are unsure about the
installation environment, please consider having it reinforced and having
the projector installed by qualified personnel. Failure to do so could result
in serious personal injury and damage to the projector.
Copyright
by InFocus Corporation
Wilsonville, OR. All rights reserved
•
To avoid personal injury, use only an approved projector mount. Using
an unauthorized projec tor mount may lead to poor ventilation and
projector failure.
•
When installing the projector mount, keep in mind that the projector’s
focus ring is not squarely in the center of the front of the projector, but
offset by several inches. Make sure that when you mount the projector
you offset the installation to match the amount of inches that the
projector’s focus ring is offset from the center of the front of the
projector.
Getting the Digital Projector Ready
Before you start the installation process, prepare your Digital Projector by
performing the following steps
(
F
IGURE
1
).
1.
Turn the projector (
C
) upside down and place it on a clean flat
surface, preferably on a towel.
2.
Locate the mounting bracket (
B
) and align it over the holes on the
projector.
3.
Locate the three (3) 4 (mm) x 8 (mm) Phillips head screws (
A
).
4.
Use the Phillips head screwdriver to secure the mounting bracket
(
B
) to the projector via the three (3) Phillips head screws (
A
). Do
not over-tighten the screws.
Figure 1
Tools Needed for Installing the Digital Projector Mount
You need the following tools to install the Digital Projector Mount:
•
Phillips head screwdriver (not included)
•
Allen wrench (included)
•
Drill (for installation environment only -
do
not
use a drill on the Digital
Projector or the Digital Projector Mount) and drill bit to match the
hardware for your installation environment (not included)
•
The commercially available hardware (
F
) that is required by your
installation environment (not included)
Projected Image Sizes
For image sizes based upon the projector’s distance to the screen,
consult the ”Projected Image Size” section in your projector’s User’s
Guide.
Hardware Description
The Digital Projector Mount utilizes the following hardware. Note that the
letters associated with the hardware on this list correspond to the letters
listed in the instructions for each installation method.
(
A
) Three (3) 4 (mm) x 8 (mm) Phillips head screws
(B) One (1) mounting bracket
(
C
) Digital Projector (not included
(
D
) Ceiling structure (not included)
(
E
) One (1) upper plate
(
F
)
SINGLE WOOD STUD
: If mounting on a single wood stud use three
(3) 5/16" x 2" Lag bolts (minimum) commercially available. Use the
mounting points on the center of the plate.
SOLID STRUCTURE
: If mounting to a solid structure use four (4)
5/16" x 2" Lag bolts (minimum) commercially available. Use the
mounting points on the outer points of the plate.
(
G
) One (1) swivel bracket (unit-attached)
