background image

2

HEALTH & SAFETY

We strongly recommend that PPE 
(Personal Protective Equipment) is 
used throughout your build to ensure 
you are protected from any potential 
health and safety risks. 

Do not 

exempt yourself from wearing PPE.

 

BEFORE YOU START

Please read through these instructions to familiarise yourself with your garden bar. We 
recommend that you 

check all the components

 using the lists found on the front and back pages 

before you start to build.

It is vital that you build your new garden bar on a solid, level base. Timber or plastic bases are 
ideal, as are concrete slabs or solid concrete.

We recommend using the following tools (not supplied):

If you have an existing base and think it is suitable for your new garden bar to be sited on, it is 
important that you check it is level and doesn’t deviate by any more than 15mm from edge to   
edge. If this is not the case, the building will twist causing gaps to appear in the sections and 
causing the roof, doors and windows to misalign.

There is more information on base preparation on our website 

www.forestgarden.co.uk

Assembly is relatively straightforward if you follow these step-by-step instructions.
We recommend aligning components properly before securing them together and 

pre-drilling

screw holes to avoid splitting the timber.

BASE

 

PREPARATION

TOOLS NEEDED

Timber Base 

Self-constructed/ 

Buy pre-made

Tape 

Measure

Sharp Knife

Pozidrive 

Screwdriver

Drill & 2mm 

Drill Bit

Hammer

Concrete

Concrete surface/ 

Concrete slabs

Pro Shed Base

Interlocking 

eco-friendly base

Soil

A base of soil or 

grass only

Broken Slabs/Gaps

Uneven slab sizes 

with no cement

REMINDER

Always pre-drill before 

screwing.

IMPORTANT

Assembly requires 2+ 

adults.

Ladder

Spirit Level

PLEASE KEEP PLASTIC BAGS AND SMALL PARTS AWAY FROM CHILDREN

Содержание SDP63GBARFP










Отзывы: