Ford Mustang 1986 страница 26 Скачать руководство пользователя

Страница: 26 / 29

P/N: 4FA020-010
© 2008 Vortech Engineering, LLC
All Rights Reserved, Intl. Copr. Secured
25MAR08 v4.0(86-93 5.0 Mus (4FA v4.0))

Example of Ignition Retard vs. Boost:

14. IGNITION/BOOST CONTROL INSTALLATION

(High Output and Cobra systems only) cont'd.

A. The Ignition/Boost Control unit is designed

to retard ignition in relation to boost.

B. The unit is adjustable from 0° of ignition

retard to 3° of ignition retard for each pound

of boost, up to a maximum of 15°.

C. Using the 1° per pound position as a starting

place, adjust the ignition retard knob until

just beyond the point of detonation. Use

third gear for testing in a safe area or road.

Adjust the retard according to changes in

altitude and fuel quality.

CAUTION:

It is extremely important

that the boost retard never

be turned to 0°. It is recom-

mended that in stock street

applications, the knob be

positioned at 1° per lb. to

start.

Fig. 15-a

15. IGNITION/BOOST CONTROL UNIT OPERATION (High Output and

Cobra Systems only)

Fig. 14-b

BOOST

RETARD

SUPERCHARGERS

Ignition/Boost

Control

MANUFACTURED FOR

VORTECH SUPERCHARGERS

MSD

BLACK

WHITE

RED

ORANGE

BLACK

WHITE

RED

ORANGE

IGNITION

COIL

FROM FACTORY COIL HARNESS

MAGNETIC PICKUP

CONNECTOR (NOT USED)

BOOST

RETARD

CONNECTOR

GROUND

TO MANIFOLD

VACUUM

5 psi at 3° per lb.

7 psi at 2° per lb.

10 psi at

1/2° per lb.

MAX.

RETARD = 15°

DEGREES

RET

ARD

5 7 10

PSI BOOST

Содержание Mustang 1986






























Результаты поиска

Содержание Mustang 1986

Отзывы:

Похожие инструкции для Mustang 1986

Бренды по названию

Популярные бренды

Ford Mustang 1986, Руководство по установке

Результаты поиска

Содержание Mustang 1986

Отзывы:

Похожие инструкции для Mustang 1986

Бренды по названию

Популярные бренды