Ford Mustang 1986 страница 21 Скачать руководство пользователя

Страница: 21 / 29

P/N: 4FA020-010

25MAR08 v4.0(86-93 5.0 Mus (4FA v4.0))

8. SMOG PUMP HOSES

A. Separate the short hose and bent hose from

the air control valve and place the shorter hose

on the diverter valve (the valve closest to the

firewall) as shown.

B. Connect the air control valve to the short

hose.

C. Trim approximately 1-1/2", or as necessary, off

the longer straight portion of the bent hose for

proper fit.

D. Secure the hose as shown with the stock

clamps.

E. It may be necessary to reroute the vacuum

control line after the supercharger is in place.

E. Attach the Vortech alternator brace

between the boss on the smog pump

and alternator with the 3/8-16 x 1" bolts.

On 1992 and later Mustangs, it may be

necessary to drill and tap the "blanked"

hole in the smog pump. To accomplish

this use an R size bit and a 3/8-16 size

tap.

F. Tighten all fasteners in the bracket/

accessory assembly.

G. Lower the entire assembly into position

and start all four fasteners that hold it

to the engine. Tighten all fasteners in a

progressive manner.

H. Reconnect alternator wires and use a tie

wrap to secure the wires.

7. MAIN BRACKET ASSEMBLY (cont'd.)

1986-93 RENEGADE

5.0L KIT ONLY

NOTE: Due to the location of the

Vortech Mondo bypass valve,

removal of the air injection hose

assemblies is required for proper

bypass valve installation. This

modification is for off-road use

only. Disregard the following steps

A thru E.

Fig. 8-a

SMOG PUMP

DIVERTER VALVE

ALVE

AIR CONTROL V

SHORTEN THIS HOSE 1-1/2”

Содержание Mustang 1986






























Результаты поиска

Содержание Mustang 1986

Отзывы:

Похожие инструкции для Mustang 1986

Бренды по названию

Популярные бренды

Ford Mustang 1986, Руководство по установке

Результаты поиска

Содержание Mustang 1986

Отзывы:

Похожие инструкции для Mustang 1986

Бренды по названию

Популярные бренды