Ford Connected Charge Station, Руководство по установке

Страница: 10 / 14

EN-
US
4 Ford Connected Charge Station Installation manual
SKML9J-10C823-BA
3.2.2 Wi-Fi
You can use Wi-Fi communication to connect the charge
station to the charging backend. This enables you to config-
ure the charger remotely through the FordPass™ app.
4
Power supply interface
connections
The terminals on the right, marked GND, X2, X1, must be con-
nected to the charging cable.
Fig. 1
The terminals on the left, marked L2, L1, GND, must be con-
nected to the mains.
Fig. 2
CAUTION
The wire colors shown in the illustrations
are for example purposes only.
Please follow the National Electrical Code (NEC) for the
appropriate wire color-coding.
5
Installation
Observe the safety information provided in section Impor-
tant Safety Information.
NOTICE
In addition to the user manual and installation manual,
follow and comply with the local regulations relating to
operation, installation, and environmental protection.
5.1 Product location considerations
When choosing the installation location for the Ford Con-
nected Charge Station, make sure that the location allows
the charging cable to reach the vehicle charge port without
straining the cable.
See Fig.19 on the inside of the back page.
You must also make sure that:
– If you are installing more than one Ford Connected
Charge Station, then you must minimally leave 200 mm
(7.9 inches) in between.
– The Ford Connected Charge Station is installed at least
900 mm (35.5 inches) above floor level.
– The mounting surface is solid and strong.
– The mounting surface is completely flat.
– The mounting surface does not have any flammable sub-
stances.
– The pavements and escape routes are not obstructed.
– You have fault-free Wi-Fi reception if you want to remote
control the charger through the Ford backend.
– The Ford Connected Charge Station is outdoor-rated;
however, for locations in intense climates, you may want
to shield the unit from intense direct sunlight and spray
to extend its useful life and fault-free operation.
5.2 Criteria for electrical connection
The Ford Connected Charge Station type label indicates the
maximum charging current that you can configure. The type
label on the Ford Connected Charge Station is located on
the right.
The power availability at the service connection determines
the maximum permitted charging current. A qualified elec-
trician must make the necessary settings in the configura-
tion. They must also verify the prerequisites for connection.
The installation must comply with the nationally applicable
regulations of authorities and power supply companies, such
as the registration of the installation of a charge station. All
protective devices specified must be designed in such a way
that every power supply pole of the Ford Connected Charge
Station is disconnected if a fault occurs. You must meet na-
tional installation regulations and standards when selecting
the protective device.
NOTICE
Do not install a GFCI (Ground Fault Circuit Interrupter).
5.2.1 DIP switch settings
WARNING
High voltages
Danger of fatal electric shock.
D1 D2 D3 D4 [A] Comment
0
0
0 0 Invalid, default
48A, 60A CB
0
0
0 1 Invalid, default
48A, 60A CB
0
0
1 0 12 A, 15A CB
D1 D2 D3 D4 [A] Comment
0
0
1 1 16 A, 20A CB
0
1
0 0 20 A, 25A CB
0
1
0 1 24 A, 30A CB
0
1
1 0 32 A, 40A CB
0
1
1 1 40 A, 50A CB
1
0
0 0 48 A, 60A CB
1
0
0 1 48 A, 60A CB
1
0
1 0 48 A, 60A CB
1
0
1 1 48 A, 60A CB
1
1
0 0 48 A, 60A CB
1
1
0 1 48 A, 60A CB
1
1
1 0 48 A, 60A CB
1
1
1 1 48 A, 60A CB
D5 Comment
0
1
Invalid, default
48A, 60A CB
5.2.2 Power supply isolation device
The Ford Connected Charge Station does not have its own
power ON/OFF switch. The protective devices installed in
the power supply system are therefore also used to discon-
nect the Ford Connected Charge Station.
5.2.3 Dimensioning the lead’s cross-
section
A qualified electrician must determine the conductor’s
cross-section / wire gauge size.
The conductor cross-section of the lead depends on:
– The maximum power availability from the service con-
nection
– The cable length