background image

Battery voltage gauge

This gauge shows the battery
voltage when the ignition is in the
ON position. If the pointer moves
and stays outside the normal
operating range (as indicated), have
the vehicle’s electrical system
checked as soon as possible.

Engine oil pressure gauge

This shows the engine oil pressure
in the system. Sufficient pressure
exists as long as the needle remains
in the normal range (the area
between the “L” and “H”).

If the gauge indicates low pressure,
stop the vehicle as soon as safely
possible and switch off the engine
immediately. Check the oil level.
Add oil if needed (refer to

Engine

oil

in the

Maintenance and care

chapter). If the oil level is correct, have your vehicle checked at your
dealership or by a qualified technician.

Fuel gauge

Displays approximately how much
fuel is in the fuel tank (when the
key is in the ON position). The fuel
gauge may vary slightly when the
vehicle is in motion. The ignition
should be in the OFF position while
the vehicle is being refueled. When
the gauge first indicates empty,
there is a small amount of reserve
fuel in the tank. When refueling the
vehicle from empty indication, the
amount of fuel that can be added will be less than the advertised
capacity due to the reserve fuel.

The FUEL DOOR icon and arrow indicates which side of the vehicle the
fuel filler door is located.

L

H

H

E

F

Instrumentation

14

Содержание 1999 Explorer









































































































































































































































































Отзывы: