Ford 1999 Explorer страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 264

background image

•

PNL

•

FLR-Distributes outside air through the instrument panel

registers and the floor ducts. Heating and air conditioning capabilities
are provided in this mode. The air will be heated or cooled based on
the temperature selection. For added customer comfort, the air
distributed through the floor ducts will be slightly warmer than the air
sent to the instrument panel registers.

•

FLOOR-Allows for maximum heating by distributing outside air
through the floor ducts. However, the air cannot be cooled below the
outside temperature because the air conditioning does not operate in
this mode.

•

FLR

•

DEF-Distributes outside air through the windshield defroster

ducts and the floor ducts. Heating and air conditioning capabilities are
provided in this mode. The air will be heated or cooled based on the
temperature selection. For added customer comfort, the air
distributed through the floor ducts will be slightly warmer than the air
sent to the windshield defroster ducts. If the temperature is about
10°C (50°F) or higher, the air conditioner will automatically
dehumidify the air to prevent fogging.

•

DEF

-Distributes outside air through the windshield defroster

ducts. It can be used to clear ice or fog from the windshield. If the
outside air temperature is about 10°C (50°F) or higher, the air
conditioner will automatically dehumidify the air to prevent fogging.

•

OFF-Outside air is shut out and the fan will not operate. For short
periods of time only, use this mode to prevent undesirable odors from
entering the vehicle.

Rear fan off

Press REAR FAN OFF to turn off
the rear console fan. This overrides
the rear console fan speed control.

VENT

PNL • FLR

MAX A/C

REAR FAN OFF

Controls and features

27

«
...
25
26
27
28
29
...
»

Содержание 1999 Explorer









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1999 Explorer

Бренд: KC HiLiTES Страницы: 4

Бренд: Valeo Страницы: 17

witty park XEV6 Series

Бренд: hager Страницы: 9

Cherokee 16 1982

Бренд: Jeep Страницы: 1311

Бренд: TATA Motors Страницы: 236

Бренд: BMW Страницы: 38

Бренд: Ford Страницы: 8

Бренд: Intec Страницы: 16

Бренд: Kuda Страницы: 2

Бренд: EUFAB Страницы: 16

Бренд: Hama Страницы: 4

Бренд: Volvo Страницы: 230

Бренд: Cadillac Страницы: 335

Бренд: Cadillac Страницы: 20

Бренд: Pyle Страницы: 8

Бренд: Hyundai Страницы: 168

Бренд: iQOS Страницы: 4

Бренд: STO N SHO Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды