Ford 1999 Explorer страница 80 Скачать руководство пользователя

Страница: 80 / 264

SPEED CONTROL (IF EQUIPPED)

To turn speed control on

•

Press ON.

Vehicle speed cannot be controlled
until the vehicle is traveling at or
above 48 km/h (30 mph).

Do not use the speed control in heavy traffic or on roads that
are winding, slippery, or unpaved.

Do not shift the gearshift lever into N (Neutral) with the speed
control on.

To turn speed control off

•

Press OFF or

•

Turn off the vehicle ignition.

Once speed control is switched off, the previously programmed set speed
will be erased.

OFF

Controls and features

Содержание 1999 Explorer









































































































































































































































































Результаты поиска

Содержание 1999 Explorer

Отзывы:

Похожие инструкции для 1999 Explorer

Бренды по названию

Популярные бренды

Ford 1999 Explorer, Руководство пользователя

Результаты поиска

Содержание 1999 Explorer

Отзывы:

Похожие инструкции для 1999 Explorer

Бренды по названию

Популярные бренды