Fontanot Genius 030 T, Руководство по сборке

Страница: 12 / 80

12 - Genius 030 - 040 T
balusters (H= 910 mm) into the 033063 components, with the 033092 reinforcing baluster about every
metre, and lock them with components 033101. Fix the balusters to the wall using component 033010 and
items 008004, 011053 and 033056 (drill with an Ø 8 mm bit). Determine the length of the handrails and
cut off the excess quantity. Assemble the 140010 or 140331 handrails to the balusters with the 002031
components using items 046011 for straight balustrades and items 001038 and 046059 for circular
balustrades. Assemble any 033103, 033105, 033107 connecting components and the 033103 terminal
components.
36. Insert the steel cables 004041 into the parts 034035 on the balusters, positioning the parts 004048 in
correspondence to the balusters at the end of the railing side. Secure the cables on one of the two ends
using the parts 004048 and 001011. Cut and secure the cables on the opposite end using the parts
004048, 001011 and 011040 (cover the cable ends with some adhesive tape to prevent them from fraying
when you cut them). Tighten the cables by screwing in part 011040 in sequence from top to bottom (Fig. 1)
(Fig. 6) (Fig. 7).
Final assembly
37. To further reinforce the staircase at intermediate points, fix components 033010 to wall and join to the
balusters, using components 033056. Drill with an 8 mm bit and use components 008004, 011053,
011057, 005035 (Fig. 12) (Fig. 13).
Assembly of 030 railing
38. Unlock component 005008 and fan out the 103008 steps. It’s now possible to ascend the staircase.
39. Fit parts BE6 into holes on treads with edge facing upwards (Fig. 2).
40. Starting from the landing, insert the 122011 connecting balusters between the steps, inserting the BE8
component on each step, with the hole in the screw facing in the direction of the ascent. If necessary, cut the
balusters 122011 from the lower end to obtain a handrail height of about 100 cm.
41. Position balusters with component C63 with the part with hole upwards (Fig. 2) (Fig. 9). Tighten the 001013
components of the steps above and below paying attention to the riser (Fig. 2).
42. Carefully check that all balusters positioned are vertical. This is essential for successful final assembly of the
staircase.
43. Definitively tighten component 005008 (Fig. 9).
44. Fix component BE5 to floor in position of first baluster, drilling with an 8 mm bit. Use components 011053,
008004, and 001004 (Fig. 2).
45. Position the first baluster 122011; adjust height according to the balusters fitted earlier (Fig. 2). Insert the
046050 reinforcing component into the 1st baluster.
46. Prepare spiral handrails (p. 52).
47. Fit parts BE5 to treads, using fittings 002040, in an intermediate position, drilling with a Ø 4,5 mm bit.
Determine the height of the intermediate columns, measuring the distance from handrail to step, deducting
5 mm for the thickness of component BE5, and cutting the balusters on the free side. Once cut, insert the
columns into the BE5 details, before fixing them to the handrail. Make sure they are vertical before tightening
them with component 001004 (Fig. 2) (Fig. 6) (Fig. 8).
48. Complete assembly of railing, fitting components BE7 into the lower part of balusters 122011 and
components 031075 into side of treads (Fig. 2).
Assembly of 030 balustrade
49. Screw component 033063 on to brace 046036 with the 011038 screws (Fig. 2). Assemble the 121028 post with
the 033149 fixing component and items 011063 and 005036, insert it into component 033063 and fix it
with items 001004, positioning the C63 tie according to the direction of the handrail.
50. Position components 033008 on landing, using components 002040 and 001004. Drill landing with a 4.5 mm
bit, keeping a distance between centres of no more than 12 cm.
51. Position balusters 122014 and tighten component 001004 (Fig. 2).
52. Fix straight handrail 140010 using components 002031 (Fig. 2).
53. Depending on position and presence of walls around the stairwell, it may be necessary to position one or two
extra balusters 122014 (Fig. 9).
54. In this case, a space must be considered that is at the same distance from the other balusters or from the
wall. Drill landing with a 5 mm bit and assemble with components 033008, 001004 and 002040 (Fig. 2).
55. Assemblyoffloor-mountedbalustrade,ifapplicable(Fig.15)
Determine the position of the posts on the floor, on average one every 12 cm and at a distance of 8 cm from
the edge.
Take care: for circular balustrades, use the circular handrail to determine the distance of the posts from