Fondital GIAVA KRB 12, Руководство по установке, использованию и техническому обслуживанию, Страница: 47 / 68

47
3.2.11. Connection to (optional) ambient thermostat
The boiler is designed to be connected to an ambient thermostat (optional, not compulsory).
Ambient thermostat contacts must be properly sized in compliance with a load of 5 mA at 24 Vdc.
Ambient thermostat cables shall be connected to electronic board pins 1 and 2 (fig. 28, 29 and 30), after having eliminated the jumper supplied as
a standard with the boiler.
The ambient thermostat cables are not to be grouped together in the same sheath as power mains supply cables.
3.2.12. Installation and operation with (optional) Open Therm Remote Control
The boiler may be connected to an Open Therm Remote Control (non-compulsory optional accessory supplied by manufacturer).
The Remote Control must only be installed by qualified personnel.
Only use original Remote Control Units supplied by the manufacturer.
The correct operation of the Remote Control itself and of the boiler is not guaranteed if non original Remote Control units not
supplied by the manufacturer are used.
To install the Remote Control, refer to the instructions provided with the Remote Control itself.
Please note the following precautions when installing the Remote Control:
- the Remote Control wiring must not be grouped together in the same sheath as the power cables: if the cables are sheathed together,
electrical interference from other power cables may compromise the functions of the Remote Control;
- the Remote Control must be installed on an indoor wall at a height of approximately 1.5 m from the floor and in a suitable location for measuring
ambient temperature: do not install in recess or corners, behind doors or curtains, and install away from heat sources, direct sunlight, air draughts
and water sprays.
The Remote Control connector is protected against inverted polarity, and the connections may be inverted.
Do not connect the remote control to mains electrical power 230 V ~ 50 Hz.
For complete instructions on how to program the Remote Control, refer to the instruction manual included in the Remote Control kit.
Board and Remote Control communicate in each operating mode: OFF, SUMMER, WINTER, CH ONLY; boiler display layout corresponds to the setting
made from the Remote Control, as for the operating mode.
The Remote Control may be used to view and set a number of special parameters denominated TSP parameters and reserved solely for qualified
technicians (tables 14 and 15).
TPS0 parameter sets default data table and restores all factory settings, cancelling all preceding modifications on single parameters.
If a single parameter is found to be incorrect, the value given in the default value table is restored.
If the user attempts to set a value not within the permissible range for the parameter, the new value is rejected and the existing value is maintained.
Parameter
Configurable
value range
Default
12 kW
Methane
gas
Default
12 kW
Propane
gas
Default
24 kW
Methane
gas
Default
24 kW
Propane
gas
Default
28 kW
Methane
gas
Default
28 kW
Propane
gas
Default
32 kW
Methane
gas
Default
32 kW
Propane
gas
P0 - TSP0
Equipment type and default data chart
0 ÷ 7 0 5 1 3 2 4 6 7
P4 - TSP4
Fan speed at burner maximum output
(DHW)
TSP5 ÷ 250 Hz 182 Hz 177 Hz 197 Hz 192 Hz 205 Hz 200 Hz 208 Hz 206 Hz
P5 - TSP5
Fan speed at burner minimum output
(DHW and CH)
25 ÷ 120 Hz 37 Hz 38 Hz 40 Hz 40 Hz 39 Hz 39 Hz 43 Hz 43 Hz
P6 - TSP6
Fan speed at ignition power and
propagation
25 ÷ 160 Hz 68 Hz 68 Hz 58 Hz 58 Hz 60 Hz 60 Hz 76 Hz 76 Hz
P7 - TSP7
Upper limit for maximum CH heat output
10 ÷ 100 % 76% 74% 88% 88% 89% 88% 89% 88%
P8 - TSP8
Negative ramp start minimum speed
P5 ÷ P6 56 56 56 56 60 60 60 60
P9 - TSP9
Negative ramp time
0 ÷ 30
(1 = 10 sec.)
18 18 25 25 18 18 18 18
P10 - TSP10
CH curves
0 ÷ 3 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Table 14 - Limits to be set for TSP parameters and default values in relation to boiler type (TSP0)