Fondital GIAVA KRB 12 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 68

Fondital GIAVA KRB 12 Скачать руководство пользователя страница 17

17

1.8.

"Manual" programme setting

The "manual" mode selection indicated with symbol

, allows activating the heating function, 24 hours a day, in both zones at the "day temperature",

disabling at the same time zone 1 and zone 2 programming. The water heater on the other side, is heated according to the specific programme.

1- Press “prog” to access the
manual programme setting
mode.

2- Press “ok” to confirm manual
programming activation.
Press "reset" to go back to the
starting page, namely to quit
the function.

1.9.

"Automatic" programme setting

The selection of "automatic" mode, identified by symbol

, allows boiler to enable heating of both zones in "day temperature" or "night

temperature", based on the programming envisaged for zone 1 and zone 2.

1- Press “prog” to access the
automatic programme setting
mode.

2- Press “ok” to confirm
automatic programming
activation. Press "reset" to
go back to the starting page,
namely to quit the function.

«
...
15
16
17
18
19
...
»

Содержание GIAVA KRB 12





































































Отзывы:

Нет отзывов