FOG QUADRA 493 9021, Установка, эксплуатация и обслуживание

Страница: 11 / 60

QUADRA
11
E 167 - GB - 6
Rue du Pré Neuf - 58440 MYENNES FRANCE
493 9021
493 9031
Anchoring the columns
Drill the holes for the anchor bolts using the base plates as templates. Ensure that the columns are as vertical
as possible and concentric in relation to the base plate holes in order to allow column adjustment. If drilling
cannot be completed with the column in place, trace the position of the holes on the floor as accurately as
possible, remove the column and its shims, noting their positions.
Fit a large washer in position under the bolt head, locate the anchor bolts in position and tighten them.
Before anchoring the motor column, ensure all the necessary parts are fitted. Check the column adjustments
(verticality, squareness and 1mm clearance), alter the shims if necessary.
Motor column assembly
While it is more convenient to assemble the motor column when it is positioned at bench height, it is also
possible to do this with the column in an upright position, secured to the ground (See Fig. 7).
CAUTION: THE MOTOR COLUMN ASSEMBLY WILL NOT STAND UPRIGHT BY
ITSELF. THE RESERVOIR FOR THE MOTOR PUMP UNIT IS MADE OF PLASTIC.
• Attach the control panel mounting plate using four TH M8 x 16 screws and serrated lock washers.
• Attach the power-pack using four TH 8 x 16 screws and serrated lock washers between the 'U' bracket
and the column and four M8 x 20 screws, serrated lock washers and M8 nuts between the motor and
the 'U' brackets).
• Position the motor coupling links as appropriate and connect the cable, route it to the left of the motor.
• Attach the upper limit switch to its bracket using two C M4 x 25 screws and serrated lock washers.
Fit the bracket to the top of column on the inside with two TH M6 x 10 screws and serrated lock washers.
• Feed the cable through the column and connect it onto the control panel.
Fitting the wire ropes
• Bring the platform to rest on the latches at about 1000 mm from the floor, by alternately raising each
cross-member 2 or 3 slots, using a crane, jack or a lever engaged in one slot of the ladder rack and a
wooden block inserted between the lever and the bottom of the vertical cheek plate.
• At each end of the fixed track, remove the wire rope guide screws (Fig. 4).
• Unwind the wire ropes over a clean floor, they have a steel core and must not be subjected to any
kinking or bending during their installation. The ends of the wire ropes are colour-coded and should
be threaded over pulley grooves of the same colour as the rope.
Insert the following into the rectangular aperture on the cross-member beam 1-2:
• The loop of the white and yellow wire ropes to the left of the twin pulleys and then route it over the
crossbar, so that the yellow wire rope (the shortest) is uppermost.
• The end of the white wire rope to the right of the twin pulleys and then bring it along the track and out
through the rectangular aperture in the side of the cross-member 3-4.
• The loop of the red and blue wire ropes to the right of the twin pulleys and then route it over the crossbar
so that the red wire rope (the shortest) is uppermost.
• The end of the blue wire rope to the left of the twin pulleys and then in a similar way as the white wire
rope and out through the other end of the track.
• Attach the nylon roller by its shoulder screw onto the end of the crossbar, on the side of the red and blue
wire ropes (inner side of the platform).
• Remove the vertical pulleys from cross-member 1-2 and then feed the end of the red and yellow wire
ropes in through the beam until they reach their respective columns. Ensure that the wire ropes are
correctly positioned in the grooves of the twin pulleys and replace the three wire rope guide screws.