FMI (V) DVF42NH Скачать руководство пользователя

Страница: 24 / 40

www.fmiproducts.com

125078-01B

inSPecting bUrnerS

Pilot

Burner

Ignitor/

Sensor

Figure 35 - Correct Pilot Flame Pattern

Sensing

Rod

Check pilot flame pattern and burner flame

patterns often.

pILOT ASSEMBLY

The pilot assembly is factory preset for the

proper flame. Alterations may have occurred

during shipping and handling. The pilot is

located on right hand side of burner.
The flame must envelope 1/4" of top of the

ignitor/sensor and grounding stem.
If your pilot assembly does not meet these

requirements:
• Turn the adjustment screw marked PILOT

clockwise to decrease or counterclockwise

to increase the flame to proper size (see

Figure 33, page 23). Do not remove the

adjustment screw.

• see

Troubleshooting

, page 26

BURNER FLAME pATTERN

Burner flames will be steady, not lifting or float

ing. Flame patterns will be different from unit

to unit and will vary depending on installation

type and weather conditions.
If the vent configuration is installed incorrectly,

flames will lift or "ghost". This can be danger

ous. Inspect flames after installation to ensure

proper installation and performance.
Figure 36 shows a typical flame pattern.
If burner flame pattern differs from that de

scribed:
• turn fireplace off (see

To Turn Off Gas to

Appliance,

page 23)

• see

Troubleshooting

, page 26

Figure 36 - Typical Flame Pattern

cLeAning AnD MAintenAnce

WARNING: Turn off fireplace

and let cool before cleaning.

CAUTION: You must keep

control areas, burners and

circulating air passageways of

fireplace clean. Inspect these

areas of fireplace before each

use. Have fireplace inspected

yearly by a qualified service

person. Fireplace may need

more frequent cleaning due to

excessive lint from carpeting,

bedding material, pet hair, etc.

GLASS DOORS

WARNING: Handle glass

door panels with care. Do not

strike, slam or otherwise abuse

glass. Do not operate fireplace

with the glass door unlatched,

removed, cracked or broken.

WARNING: Do not use

abrasive cleaners as this may

damage glass. Use a nonabra

sive household glass cleaner to

clean glass. Do not clean glass

when hot.

Содержание (V) DVF42NH









































Результаты поиска

Содержание (V) DVF42NH

Отзывы:

Похожие инструкции для (V) DVF42NH

Бренды по названию

Популярные бренды

FMI (V) DVF42NH, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание (V) DVF42NH

Отзывы:

Похожие инструкции для (V) DVF42NH

Бренды по названию

Популярные бренды