background image

www.fmiproducts.com

125078-01B

5

Figure 1 - Direct Vent Fireplace

Outer 

Glass Door

Log Set

Flue Collar

Nailing Flange

Lower Door/ 

Control Cover

Herringbone Brick 

Refractories

PrODUct iDentiFicAtiOn

Grate

PrODUct FeAtUreS

These are a few facts that can help you under

-

stand and enjoy your direct vent fireplace:
•  The venting system may be routed to the 

outside of your home in several ways. It 

may  vent  through  the  roof  (vertical)  or  it 

may vent to an outside/exterior wall (hori

-

zontal). The vent pipe installation is very 

important  to  allow  for  proper  operation. 

You  must  follow  the  venting  instructions 

very carefully for either vertical or horizontal 

applications.

•  This fireplace may be installed in any room 

of your house provided all local codes and 

these installation instructions are followed.

•  Each time you turn on your fireplace, you 

may notice some amount of condensation 

on the inside of the fireplace glass. This 

is  normal  and  will  disappear  after  10-20 

minutes of operation.

•  Your  direct  vent  gas  fireplace  system 

(fireplace and venting) is a balanced and 

sealed gas operating unit. It requires ap

-

proximately  10-20  minutes  of  operating 

time before the flame pattern stabilizes.

Содержание (V) DVF42NH









































Отзывы: