FMI TF18NV Скачать руководство пользователя страница 23

Страница: 23 / 48

www.fmiproducts.com

125566-01C

INSTALLATION

Continued

Figure 45 - Installing Log # 9

Figure 44 - Installing Log # 8

Figure 43 - Installing Log # 7

6. Place the right rear chunk log (#7) on top

of the middle log (#2) and rear log (#1)

as shown in Figure 43. Match the round

peg on the top of the rear log (#1) with

the round hole on the bottom of the right

rear chunk (#7) log and square peg on

the top of the middle log (#2) with the

square hole on the bottom of the right

rear chunk log (#7).

7. Place the front right mid log (#8) on top of

the front right log (#4) as shown in Figure

44. Match the round metal pin on the top

of the front right log (#4) with the round

hole on the bottom of the front right mid

log (#8).

8. Place the top right log (#9) on top of the

right rear chunk log (#7) and front right

mid log (#8) as shown in Figure 45.

Match the round peg on the top of the

right rear chunk log (#7) with the round

hole on the bottom of the top right log

(#9) and square peg on the top of the

front right mid log (#8) with the square

hole on the bottom of the top right log

(#9).

Round

Peg

Metal

Round

Peg

Square

Peg

Square Peg

9. Place the right rear top log (#10) on top of

the right rear chunk log (#7) as shown in

Figure 46, page 24. Match the rectangular

peg on the top of the right rear chunk log

(#7) with the rectangular hole on the bot-

tom of the right rear top log (#10).

10. Place the left top log (#11) on top of the

left back top log (#5) and left top forked

log (#6) as shown in Figure 47, page 24.

Match the round peg on the top of the left

top forked log (#6) with the round hole on

the bottom of the top left log (#11) and

rectangular peg on the top of the left back

top log (#5) with the rectangular hole on

the bottom of the top left log (#11).

11. Final Assembly is shown in Figure 48,

page 24.

Содержание TF18NV

















































Результаты поиска

Содержание TF18NV

Отзывы:

FMI TF18NV, Руководство владельца по эксплуатации и установке, Страница: 23 / 48

Результаты поиска

Содержание TF18NV

Отзывы: